Wear behaviour of steel coatings produced by friction surfacing

被引：55

作者：

Pereira, D. ^{[1
]}

Gandra, J. ^{[2
]}

Pamies-Teixeira, J. ^{[1
]}

Miranda, R. M. ^{[1
]}

Vilaca, P. ^{[3
]}

机构：

[1] Univ Nova Lisboa, Fac Ciencias & Tecnol, Dept Engn Mecan & Ind, UNIDEMI, P-2829516 Caparica, Portugal

[2] Univ Tecn Lisboa, Inst Super Tecn, P-1049001 Lisbon, Portugal

[3] Aalto Univ, Sch Engn, Dept Engn Design & Prod, FI-00076 Aalto, Finland

来源：

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY | 2014年 / 214卷 / 12期

关键词：

Friction surfacing; Wear; Pin-on-disc; Multi-layer; Mild steel;

D O I：

10.1016/j.jmatprotec.2014.06.003

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Friction surfacing was performed to produce multi-layer coatings of AISI 1024, AISI 1045 and AISI H13 over mild steel substrates where a continuous joining was achieved between adjacent layers and between the clad and the substrate. Microscopic and hardness characterization revealed the presence of bainitic and martensitic microstructures which influenced the hardness of the coatings. The study aimed to determine which material combination was more wear-resistant. The analysis suggested that AISI 1024 presents the least wear, both in terms of friction coefficient and wear rate. This is due to the formation of adherent protective oxide layer which is not present in both the AISI 1045 and AISI H13 steels. (c) 2014 Elsevier B.V. All rights reserved.

引用

页码：2858 / 2868

页数：11

共 24 条

[1]

[Anonymous], 1992, TRIBOLOGY FRICTION W

[2] The effect of metal type and multi-layering on friction surfacing [J].

Batchelor, AW ;

Jana, S ;

Koh, CP ;

Tan, CS .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 1996, 57 (1-2) :172-181

[3]

Bedford G.M., 1985, P 1 INT C SURF ENG B, P279

[4]

Dunkerton S.B., 1984, P C REP RECL LOND

[5] The effect of oxide-forming alloying elements on the high temperature wear of a hot work steel [J].

Fontalvo, GA ;

Mitterer, C .

WEAR, 2005, 258 (10) :1491-1499

[6] Friction surfacing-A review [J].

Gandra, J. ;

Krohn, H. ;

Miranda, R. M. ;

Vilaca, P. ;

Quintino, L. ;

dos Santos, J. F. .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2014, 214 (05) :1062-1093

[7] Performance analysis of friction surfacing [J].

Gandra, J. ;

Miranda, R. M. ;

Vilaca, P. .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2012, 212 (08) :1676-1686

[8] Effect of overlapping direction in multipass friction stir processing [J].

Gandra, J. ;

Miranda, R. M. ;

Vilaca, P. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2011, 528 (16-17) :5592-5599

[9]

Gandra J., 2013, THESIS UTL

[10] Effects of supply of fine oxide particles onto rubbing steel surfaces on severe-mild wear transition and oxide film formation [J].

Kato, H. .

TRIBOLOGY INTERNATIONAL, 2008, 41 (08) :735-742

← 1 2 3 →