Effect of Tool Pin Eccentricity on the Microstructure and Mechanical Properties of Friction Stir Processed Al-6061 Alloy

被引：8

作者：

Chen, Yu ^{[1
]}

Wang, He ^{[2
]}

Ding, Hua ^{[2
]}

Zhao, Jingwei ^{[3
]}

Zhang, Fenghe ^{[1
]}

Ren, Zhaohui ^{[1
]}

机构：

[1] Northeastern Univ, Sch Mech Engn & Automat, Shenyang 110819, Liaoning, Peoples R China

[2] Northeastern Univ, Sch Mat Sci & Engn, Shenyang 110819, Liaoning, Peoples R China

[3] Univ Wollongong, Sch Mech Mat Mechaton & Biomed Engn, Wollongong, NSW 2522, Australia

来源：

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE | 2019年 / 28卷 / 05期

基金：

美国国家科学基金会;

关键词：

aluminum alloy; friction stir processing; mechanical properties; microstructure; pin eccentricity; PARAMETERS; PROFILE; ZONE; HARDNESS; COPPER;

D O I：

10.1007/s11665-019-04025-y

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Three different stir tools with the pin eccentricity of 0, 0.4 and 0.8mm were applied to the friction stir processing (FSP) of Al-6061 alloy. Results show that the pin-affected zone (PAZ) enlarges and the grain size in the stir zone (SZ) decreases as the pin eccentricity increases. Moreover, the low peak FSP temperature induced by the pin eccentricity gives rise to the coarsening of strengthening precipitates in the SZ. Compared with the pin-eccentric FSP samples, the SZ produced without pin eccentricity exhibits the highest hardness and yield strength due to the high amount of fine precipitates. However, the application of pin eccentricity elevates the overall tensile properties of FSP samples through changing the failure location from heat-affected zone (HAZ) to SZ.

引用

页码：2845 / 2852

页数：8

共 23 条

[1] An Investigation into Microstructures and Mechanical Properties of AA7075-T6 during Friction Stir Welding at Relatively High Rotational Speeds [J].

Azimzadegan, T. ;

Serajzadeh, S. .

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2010, 19 (09) :1256-1263

[2] Microstructural and Mechanical Characterization of a Dissimilar Friction Stir-Welded AA5083-AA7B04 Butt Joint [J].

Chen, Yu ;

Ding, Hua ;

Cai, Zhihui ;

Zhao, Jingwei ;

Li, Jizhong .

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2017, 26 (02) :530-539

[3] Effect of initial base metal temper on microstructure and mechanical properties of friction stir processed A1-7B04 alloy [J].

Chen, Yu ;

Ding, Hua ;

Cai, Zhihui ;

Zhao, Jingwei ;

Li, Jizhong .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2016, 650 :396-403

[4] Influence of multi-pass friction stir processing on the microstructure and mechanical properties of Al-5083 alloy [J].

Chen, Yu ;

Ding, Hua ;

Li, Jizhong ;

Cai, Zhihui ;

Zhao, Jingwei ;

Yang, Wenjing .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2016, 650 :281-289

[5] Periodical plastic flow pattern in friction stir processed Al-Mg alloy [J].

Cui, G. R. ;

Ma, Z. Y. ;

Li, S. X. .

SCRIPTA MATERIALIA, 2008, 58 (12) :1082-1085

[6] Natural aging behaviour of friction stir welded 6005A-T6 aluminium alloy [J].

Dong, Peng ;

Sun, Daqian ;

Li, Hongmei .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2013, 576 :29-35

[7] Influences of tool pin profile and welding speed on the formation of friction stir processing zone in AA2219 aluminium alloy [J].

Elangovan, K. ;

Balasubramanian, V. .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2008, 200 (1-3) :163-175

[8] Influences of tool pin profile and tool shoulder diameter on the formation of friction stir processing zone in AA6061 aluminium alloy [J].

Elangovan, K. ;

Balasubramanian, V. .

MATERIALS & DESIGN, 2008, 29 (02) :362-373

[9] Influences of pin profile and rotational speed of the tool on the formation of friction stir processing zone in AA2219 aluminium alloy [J].

Elangovan, K. ;

Balasubramanian, V. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2007, 459 (1-2) :7-18

[10] An analytical model of heat generation for eccentric cylindrical pin in friction stir welding [J].

Essa, Ahmed Ramadan Shaaban ;

Ahmed, Mohamed Mohamed Zaky ;

Mohamed, Abdel-Karim Yousif Ahmed ;

El-Nikhaily, Ahmed Essa .

JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2016, 5 (03) :234-240

← 1 2 3 →