Characterisation of precipitation upon cooling of an AA2618 Al-Cu-Mg alloy

被引：20
作者：
Chobaut, N. [1 ]
Carron, D. [2 ]
Drezet, J. -M. [1 ]
机构：
[1] Ecole Polytech Fed Lausanne, Lab Simulat Mat, Stn 12, CH-1015 Lausanne, Switzerland
[2] Univ Bretagne Sud, LIMATB, EA 4250, F-56100 Lorient, France
来源：
JOURNAL OF ALLOYS AND COMPOUNDS | 2016年 / 654卷
关键词：
Aluminum alloys; Precipitation; Resistivity; Calorimetry; Gleeble machine; RESIDUAL-STRESS; RESISTIVITY; DIAGRAMS; BEHAVIOR; KINETICS;
D O I：
10.1016/j.jallcom.2015.09.113
中图分类号：
O64 [物理化学（理论化学）、化学物理学];
学科分类号：
070304 ; 081704 ;
摘要：
The precipitation of an AA2618 Al-Cu-Mg alloy is monitored during isothermal holdings and continuous coolings. The Time-Temperature-Property and Continuous-Cooling-Precipitation diagrams of AA2618 are obtained using in-situ resistivity and differential scanning calorimetry respectively. The two precipitation domains observed at high temperature and low temperature (< 300 degrees C) are discussed with regard to their influence on the mechanical properties during quenching of large components. (C) 2015 Elsevier B.V. All rights reserved.
引用
收藏
页码：56 / 62
页数：7
相关论文
共 30 条
  • [1] High temperature precipitation kinetics and TTT curve of a 7xxx alloy by in-situ electrical resistivity measurements and differential calorimetry
    Archambault, P
    Godard, D
    [J]. SCRIPTA MATERIALIA, 2000, 42 (07) : 675 - 680
  • [2] An analysis of thermo-mechanical treatments of a 2618 aluminium alloy: study of optimum conditions for warm forging
    Bardi, F
    Cabibbo, M
    Spigarelli, S
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2002, 334 (1-2): : 87 - 95
  • [3] Cavaliere P, 2002, MULTIPLATFORM C APPL, V2, P247
  • [4] Quench induced residual stress prediction in heat treatable 7xxx aluminium alloy thick plates using Gleeble interrupted quench tests
    Chobaut, N.
    Carron, D.
    Arsene, S.
    Schloth, P.
    Drezet, J. -M.
    [J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2015, 222 : 373 - 380
  • [5] Chobaut N., 2015, THESIS EPFL, DOI [http://dx.doi.org/10.5075/epfl-thesis-6559, DOI 10.5075/EPFL-THESIS-6559]
  • [6] Quench-Induced Stresses in AA2618 Forgings for Impellers: A Multiphysics and Multiscale Problem
    Chobaut, Nicolas
    Saelzle, Peter
    Michel, Gilles
    Carron, Denis
    Drezet, Jean-Marie
    [J]. JOM, 2015, 67 (05) : 984 - 990
  • [7] Monitoring precipitation kinetics in heat treatable aluminium alloys using in-situ resistivity in Gleeble thermomechanical simulator
    Chobaut, Nicolas
    Carron, Denis
    Drezet, Jean-Marie
    [J]. ALUMINIUM ALLOYS 2014 - ICAA14, 2014, 794-796 : 921 - +
  • [8] In situ evaluation of the microstructure evolution during rapid hardening of an Al-2.5Cu-1.5Mg (wt.%) alloy
    Deschamps, A.
    Bastow, T. J.
    de Geuser, F.
    Hill, A. J.
    Hutchinson, C. R.
    [J]. ACTA MATERIALIA, 2011, 59 (08) : 2918 - 2927
  • [9] Pre-precipitation study in the 7012 Al-Zn-Mg-Cu alloy by electrical resistivity
    Ferragut, R
    Somoza, A
    Torriani, I
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2002, 334 (1-2): : 1 - 5
  • [10] Godard D, 1999, JAPAN INSTITUTE OF METALS, PROCEEDINGS, VOL 12, (JIMIC-3), PTS 1 AND 2, P145
123