Evaluation of very high cycle fatigue zones in 42CrMo4 steel with plate-like alumina inclusions

被引：18
作者：
Seleznev, M. [1 ]
Merson, E. [2 ]
Weidner, A. [1 ]
Biermann, H. [1 ]
机构：
[1] Tech Univ Bergakad Freiberg, Inst Mat Engn, Gustav Zenner Str 5, D-09599 Freiberg, Germany
[2] Togliatti State Univ, Inst Adv Technol, Tolyatti 445020, Russia
来源：
INTERNATIONAL JOURNAL OF FATIGUE | 2019年 / 126卷
关键词：
Ultrasonic fatigue testing (USFT); Very high cycle fatigue (VHCF); Confocal laser scanning microscopy (CLSM); Non-metallic inclusions (NMI); Roughness; HIGH-STRENGTH STEELS; REGIME N-GREATER-THAN-10(7) CYCLES; SUBSURFACE CRACK INITIATION; NONMETALLIC INCLUSIONS; PROPAGATION MECHANISM; BEHAVIOR; GROWTH; LIFE; FAILURE; FILTERS;
D O I：
10.1016/j.ijfatigue.2019.05.011
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
Quenched and nitrided 42CrMo4 specimens, treated by different reactive filters were tested in very high cycle fatigue regime using ultrasonic method. Despite total alumina reduction fatigue limit showed no improvement due to large alumina plates whose parameters were studied. Areal roughness of fatigue crack zones was measured by confocal laser scanning microscopy. Periodic arrest marks were studied and used for crack growth rate calculation. Smooth area was experimentally defined as a zone between fine granular area and fisheye by imaging, roughness minima, fixed Delta K = 6.4 and crack growth rate of similar to 10(-10) m/cycle. Classification of internal crack zones is proposed.
引用
收藏
页码：258 / 269
页数：12
相关论文
共 41 条
  • [1] Reactive Filters for Steel Melt Filtration
    Aneziris, Christos G.
    Dudczig, Steffen
    Emmel, Marcus
    Berek, Harry
    Schmidt, Gert
    Hubalkova, Jana
    [J]. ADVANCED ENGINEERING MATERIALS, 2013, 15 (1-2) : 46 - 59
  • [2] Melting, Remelting, and Casting for Clean Steel
    Campbell, John
    [J]. STEEL RESEARCH INTERNATIONAL, 2017, 88 (01)
  • [3] Non-metallic inclusions in aluminium killed steels
    Dekkers, R
    Blanpain, B
    Wollants, P
    Haers, F
    Vercruyssen, C
    Gommers, B
    [J]. IRONMAKING & STEELMAKING, 2002, 29 (06) : 437 - 444
  • [4] Characterization of carbon-bonded alumina filters with active or reactive coatings in a steel casting simulator
    Dudczig, S.
    Aneziris, C. G.
    Emmel, M.
    Schmidt, G.
    Hubalkova, J.
    Berek, H.
    [J]. CERAMICS INTERNATIONAL, 2014, 40 (10) : 16727 - 16742
  • [5] Edel K.-O., 2015, EINFUHRUNG BRUCHMECH, DOI [10.1007/978-3-662-44264-7., DOI 10.1007/978-3-662-44264-7]
  • [6] Effect of Crucible Material for Ingot Casting on Detrimental Non-Metallic Inclusions and the Resulting Mechanical Properties of 18CrNiMo7-6 Steel
    Henschel, Sebastian
    Gleinig, Johannes
    Lippmann, Tim
    Dudczig, Steffen
    Aneziris, Christos G.
    Biermann, Horst
    Krueger, Lutz
    Weidner, Anja
    [J]. ADVANCED ENGINEERING MATERIALS, 2017, 19 (09)
  • [7] The nature and the mechanism of crack initiation and early growth for very-high-cycle fatigue of metallic materials - An overview
    Hong, Youshi
    Sun, Chengqi
    [J]. THEORETICAL AND APPLIED FRACTURE MECHANICS, 2017, 92 : 331 - 350
  • [8] Influence of hydrogen content and microstructure on the fatigue behaviour of steel SAE 52100 in the VHCF regime
    Karsch, T.
    Bomas, H.
    Zoch, H. -W.
    Maendl, S.
    [J]. INTERNATIONAL JOURNAL OF FATIGUE, 2014, 60 : 74 - 89
  • [9] Influence of non-metallic inclusions on fatigue life in the very high cycle fatigue regime
    Krewerth, D.
    Lippmann, T.
    Weidner, A.
    Biermann, H.
    [J]. INTERNATIONAL JOURNAL OF FATIGUE, 2016, 84 : 40 - 52
  • [10] Application of full-surface view in situ thermography measurements during ultrasonic fatigue of cast steel G42CrMo4
    Krewerth, Dominik
    Lippmann, Tim
    Weidner, Anja
    Biermann, Horst
    [J]. INTERNATIONAL JOURNAL OF FATIGUE, 2015, 80 : 459 - 467
12345