Multiple Performance characteristics Optimization in the Turning Process of AISI H13 Tool Steel using Taguchi and Fuzzy Logic

被引：0

作者：

Soepangkat, Bobby O. P. ^{[1
]}

Pramujati, Bambang ^{[1
]}

Karuniawan, Bayu W.

机构：

[1] Inst Teknol Sepuluh Nopember ITS, Dept Mech Engn, Mfg Proc Lab, Surabaya 60111, Indonesia

来源：

ADVANCES IN APPLIED MECHANICS AND MATERIALS | 2014年 / 493卷

关键词：

Fuzzy logics; Multiple performance characteristics; Taguchi method; Turning;

D O I：

10.4028/www.scientific.net/AMM.493.583

中图分类号：

TH [机械、仪表工业];

学科分类号：

0802 ;

摘要：

This paper presents the application of Taguchi's method of orthogonal array and signal to noise ratio with logical fuzzy reasoning for multiple output optimization of turning AISI H13 steel using carbide tool. The cutting parameters, i.e., cutting speed, feed rate, depth of cut and nose radius, are optimized with considerations of multiple performance characteristics such as cutting force, feed force, surface roughness and tool flank wear. Experimental results are provided to illustrate the effectiveness of this approach.

引用

页码：583 / +

页数：2

共 50 条

[31] Optimization of machining parameters in turning GFRP composites using a carbide (K10) tool based on the Taguchi method with fuzzy logics [J].

Palanikumar, K. ;

Karunamoorthy, L. ;

Karthikeyan, R. ;

Latha, B. .

METALS AND MATERIALS INTERNATIONAL, 2006, 12 (06) :483-491

[32] Optimization of end milling parameters and determination of the effects of edge profile for high surface quality of AISI H13 steel by using precise and fast measurements [J].

Durakbasa, M. Numan ;

Akdogan, Anil ;

Vanli, Ali Serdar ;

Bulutsuz, Asli Gunay .

MEASUREMENT, 2015, 68 :92-99

[33] Investigation of wear and surface quality of raw AISI H13 hot work tool steel in electro-discharge machining machine [J].

Nas, Engin ;

Zurnaci, Erman ;

Gueltekin, Sidika Yildirim .

IRONMAKING & STEELMAKING, 2025,

[34] Optimization of micro-EDM with multiple performance characteristics using Taguchi method and Grey relational analysis [J].

Natarajan, N. ;

Arunachalam, R. M. .

JOURNAL OF SCIENTIFIC & INDUSTRIAL RESEARCH, 2011, 70 (07) :500-505

[35] Optimization of WEDM process of pure titanium with multiple performance characteristics using Taguchi's DOE approach and utility concept [J].

Chalisgaonkar R. ;

Kumar J. .

Frontiers of Mechanical Engineering, 2013, 8 (2) :201-214

[36] Hybrid GRA-PCA and modified weighted TOPSIS coupled with Taguchi for multi-response process parameter optimization in turning AISI 1040 steel [J].

Sultana, Mst Nazma ;

Dhar, Nikhil Ranjan .

ARCHIVE OF MECHANICAL ENGINEERING, 2021, 68 (01) :23-49

[37] Optimization of the Surface Roughness and Chip Compression Ratio of Duplex Stainless Steel in a Wet Turning Process Using the Taguchi Method [J].

Gyliene, Virginija ;

Brasas, Algimantas ;

Ciuplys, Antanas ;

Jablonskyte, Janina .

MACHINES, 2024, 12 (07)

[38] Application of grey fuzzy logic for the optimization of drilling parameters for CFRP composites with multiple performance characteristics [J].

Krishnamoorthy, A. ;

Boopathy, S. Rajendra ;

Palanikumar, K. ;

Davim, J. Paulo .

MEASUREMENT, 2012, 45 (05) :1286-1296

[39] Minimization of Milling-Induced Residual Stresses in AISI 1045 Steel: Process Optimization using Design of Experiments Taguchi Method [J].

Durakovic, Benjamin ;

Marimuthu, K. Prakash .

JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2024, 33 (15) :7721-7727

[40] Optimization and Modeling of Process Parameters in Multi-Hole Simultaneous Drilling Using Taguchi Method and Fuzzy Logic Approach [J].

Aamir, Muhammad ;

Tu, Shanshan ;

Tolouei-Rad, Majid ;

Giasin, Khaled ;

Vafadar, Ana .

MATERIALS, 2020, 13 (03)

← 1 2 3 4 5 →