An investigation into the warm deformation behavior of Ti-6Al-1.5Cr-2.5Mo-0.5Fe-0.3Si alloy

被引:14
作者
Ghasemi, E. [1 ]
Zarei-Hanzaki, A. [1 ]
Moemeni, S. [1 ]
Ghambari, M. [2 ]
Rezaee, M. [1 ]
机构
[1] Univ Tehran, Sch Met & Mat Engn, Coll Engn, Complex Lab Hot Deformat & Thermomech Proc High P, Tehran, Iran
[2] Univ Tehran, Sch Met & Mat Engn, Coll Engn, Tehran, Iran
来源
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2016年 / 654卷
关键词
Titanium alloys; Warm compression; Adiabatic shear banding; Microstructural evolution; TI-6AL-7NB BIOMEDICAL ALLOY; COLONY ALPHA MICROSTRUCTURE; 2-PHASE TITANIUM-ALLOY; HOT-WORKING; DYNAMIC RECRYSTALLIZATION; FLOW BEHAVIOR; GLOBULARIZATION KINETICS; PHASE-TRANSFORMATION; SINGLE-PHASE; EVOLUTION;
D O I
10.1016/j.msea.2015.12.065
中图分类号
TB3 [工程材料学];
学科分类号
0805 ; 080502 ;
摘要
The microstructural evolution and the flow behavior of Ti-6Al-1.5Cr-2.5Mo-0.5Fe-0.3Si alloy were investigated in this research. The flow behavior of the alloy at temperatures in the range of 100-600 degrees C was studied using warm compression testing under the strain rate of 0.001-0.1 s(-1). The results indicate that the formability of the alloy is significantly increased at temperatures higher than 400 degrees C due to the activation of pyramidal slip systems. Moreover, optical observations confirm the occurrence of flow localization and adiabatic shear banding within the microstructure due to the adiabatic heating phenomenon at lower temperatures. The adiabatic heating is also led the experimental material to exhibit a negative strain rate sensitivity behavior. The tensile deformation behavior of this alloy was also studied at temperatures in the range of 100-400 degrees C through warm tension testing. The results show that the alpha phase grains are elongated along the tensile direction at lower temperatures but would be globularized at higher temperatures. (C) 2015 Elsevier B.V. All rights reserved.
引用
收藏
页码:264 / 270
页数:7
相关论文
共 35 条
[1]   Modeling the hot working behavior of near-α titanium alloy IMI 834 [J].
Balasundar, I. ;
Raghu, T. ;
Kashyap, B. P. .
PROGRESS IN NATURAL SCIENCE-MATERIALS INTERNATIONAL, 2013, 23 (06) :598-607
[2]  
Changjian G., 2014, RARE METAL MAT ENG, V43, P2069
[3]   Strain-induced phase transformation during thermo-mechanical processing of titanium alloys [J].
Dehghan-Manshadi, Ali ;
Dippenaar, Rian J. .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2012, 552 :451-456
[4]  
Dodd B., 1992, ADIABATIC SHEAR LOCA
[5]   Dynamic recovery and recrystallization in titanium alloys by hot deformation [J].
Furuhara, T. ;
Poorganji, B. ;
Abe, H. ;
Maki, T. .
JOM, 2007, 59 (01) :64-67
[6]   The adiabatic correction factor for deformation heating during the uniaxial compression test [J].
Goetz, RL ;
Semiatin, SL .
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2001, 10 (06) :710-717
[7]   A model of continuous dynamic recrystallization [J].
Gourdet, S ;
Montheillet, F .
ACTA MATERIALIA, 2003, 51 (09) :2685-2699
[8]   The microstructural evolution of near beta alloy Ti-10V-2Fe-3Al during subtransus forging [J].
Jackson, M ;
Dashwood, R ;
Christodoulou, L ;
Flower, H .
METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2005, 36A (05) :1317-1327
[9]   Microstructural evolution and modelling of the hot compression of a TC6 titanium alloy [J].
Li, MQ ;
Xiong, AM ;
Huang, WC ;
Wang, HR ;
Su, SB ;
Shen, LC .
MATERIALS CHARACTERIZATION, 2002, 49 (03) :203-209
[10]   Deformation behavior of TC6 alloy in isothermal forging [J].
Li, XK ;
Li, MQ ;
Zhu, DS ;
Xiong, AM .
JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2005, 14 (05) :671-676