Diagnosis of Patellofemoral Pain Syndrome Based on a Multi-Input Convolutional Neural Network With Data Augmentation

被引:4
|
作者
Shi, Wuxiang [1 ,2 ]
Li, Yurong [2 ]
Xiong, Baoping [2 ,3 ]
Du, Min [1 ,2 ,4 ]
机构
[1] Fuzhou Univ, Coll Phys & Informat Engn, Fuzhou, Peoples R China
[2] Fuzhou Univ, Fujian Key Lab Med Instrumentat & Pharmaceut Tech, Fuzhou, Peoples R China
[3] Fujian Univ Technol, Dept Math & Phys, Fuzhou, Peoples R China
[4] Wuyi Univ, Fujian Prov Key Lab Ecoind Green Technol, Wuyishan, Peoples R China
关键词
patellofemoral pain syndrome; convolutional neural network; data preprocessing; data augmentation; biomechanical analysis;
D O I
10.3389/fpubh.2021.643191
中图分类号
R1 [预防医学、卫生学];
学科分类号
1004 ; 120402 ;
摘要
Patellofemoral pain syndrome (PFPS) is a common disease of the knee. Despite its high incidence rate, its specific cause remains unclear. The artificial neural network model can be used for computer-aided diagnosis. Traditional diagnostic methods usually only consider a single factor. However, PFPS involves different biomechanical characteristics of the lower limbs. Thus, multiple biomechanical characteristics must be considered in the neural network model. The data distribution between different characteristic dimensions is different. Thus, preprocessing is necessary to make the different characteristic dimensions comparable. However, a general rule to follow in the selection of biomechanical data preprocessing methods is lacking, and different preprocessing methods have their own advantages and disadvantages. Therefore, this paper proposes a multi-input convolutional neural network (MI-CNN) method that uses two input channels to mine the information of lower limb biomechanical data from two mainstream data preprocessing methods (standardization and normalization) to diagnose PFPS. Data were augmented by horizontally flipping the multi-dimensional time-series signal to prevent network overfitting and improve model accuracy. The proposed method was tested on the walking and running datasets of 41 subjects (26 patients with PFPS and 15 pain-free controls). Three joint angles of the lower limbs and surface electromyography signals of seven muscles around the knee joint were used as input. MI-CNN was used to automatically extract features to classify patients with PFPS and pain-free controls. Compared with the traditional single-input convolutional neural network (SI-CNN) model and previous methods, the proposed MI-CNN method achieved a higher detection sensitivity of 97.6%, a specificity of 76.0%, and an accuracy of 89.0% on the running dataset. The accuracy of SI-CNN in the running dataset was about 82.5%. The results prove that combining the appropriate neural network model and biomechanical analysis can establish an accurate, convenient, and real-time auxiliary diagnosis system for PFPS to prevent misdiagnosis.
引用
收藏
页数:9
相关论文
共 50 条
  • [31] A multi-input multi-output functional artificial neural network
    Newcomb, RW
    deFigueiredo, RJP
    JOURNAL OF INTELLIGENT & FUZZY SYSTEMS, 1996, 4 (03) : 207 - 213
  • [32] Multi-Input Deep Convolutional Neural Network Model for Short-Term Power Prediction of Photovoltaics
    Zhang, Huimin
    Zhao, Yang
    Kang, Huifeng
    Mei, Erzhao
    Han, Haimin
    COMPUTATIONAL INTELLIGENCE AND NEUROSCIENCE, 2022, 2022
  • [33] A multi-input parallel convolutional attention network for tool wear monitoring
    Liu, Qiang
    Li, Dingkun
    Ma, Jing
    Wei, Xudong
    Bai, Zhengyan
    INTERNATIONAL JOURNAL OF COMPUTER INTEGRATED MANUFACTURING, 2025, 38 (01) : 23 - 39
  • [34] Synergistic drug combination prediction in multi-input neural network
    Chen X.
    Qin Y.
    Chen M.
    Zhang C.
    Shengwu Yixue Gongchengxue Zazhi/Journal of Biomedical Engineering, 2020, 37 (04): : 676 - 682
  • [35] Uniform Experimental Design for Optimizing the Parameters of Multi-input Convolutional Neural Networks
    Lin, Cheng-Jian
    Wu, Chen-Hsien
    Sun, Chi-Chia
    Lin, Cheng-Hsien
    SENSORS AND MATERIALS, 2020, 32 (10) : 3137 - 3155
  • [36] Investigation of multi-input convolutional neural networks for the prediction of particleboard mechanical properties
    Chen, Shuoye
    Sakai, Shunsuke
    Matsuo-Ueda, Miyuki
    Umemura, Kenji
    SCIENTIFIC REPORTS, 2025, 15 (01):
  • [37] The Impact of Multi-optimizers and Data Augmentation on TensorFlow Convolutional Neural Network Performance
    Taqi, Arwa Mohammed
    Awad, Ahmed
    Al-Azzo, Fadwa
    Milanova, Mariofanna
    IEEE 1ST CONFERENCE ON MULTIMEDIA INFORMATION PROCESSING AND RETRIEVAL (MIPR 2018), 2018, : 140 - 145
  • [38] Estimation of beef marbling standard for live cattle using multi-input convolutional neural network with ultrasound images
    Katayama, Toshiki
    Kawada, Hirohumi
    Nishiyama, Masashi
    Iwai, Yoshio
    FIFTEENTH INTERNATIONAL CONFERENCE ON QUALITY CONTROL BY ARTIFICIAL VISION, 2021, 11794
  • [39] Human Activity Recognition Based on Multichannel Convolutional Neural Network With Data Augmentation
    Shi, Wenbing
    Fang, Xianjin
    Yang, Gaoming
    Huang, Ji
    IEEE ACCESS, 2022, 10 : 76596 - 76606
  • [40] Enhancing flood susceptibility modeling using integration of multi-source satellite imagery and multi-input convolutional neural network
    Maddah, Shadi
    Mojaradi, Barat
    Alizadeh, Hosein
    NATURAL HAZARDS, 2025, 121 (03) : 2801 - 2824