Influence of layer thickness on mechanical properties of multilayered NiFe samples processed by electrodeposition

被引：18
|
作者：
Kurmanaeva, L. [1 ]
McCrea, J. [2 ]
Jian, J. [3 ]
Fiebig, J. [1 ]
Wang, H. [3 ]
Mukherjee, A. K. [1 ]
Lavernia, E. J. [1 ,4 ]
机构：
[1] Univ Calif Davis, Dept Chem Engn & Mat Sci, Davis, CA 95817 USA
[2] Integran Technol Inc, Toronto, ON, Canada
[3] Texas A&M Univ, Dept Elect & Comp Engn, College Stn, TX 77843 USA
[4] Univ Calif Irvine, Dept Chem Engn & Mat Sci, Irvine, CA 92697 USA
来源：
MATERIALS & DESIGN | 2016年 / 90卷
关键词：
Ni-Fe; Electrodeposition; Multilayered structure; Nanoindentation; EDS; DEFORMATION MECHANISMS; BEHAVIOR; ALLOYS; STABILITY;
D O I：
10.1016/j.matdes.2015.10.137
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
Multilayered (ML) NiFe thick foils have been studied in order to provide insight in synthesizing structure-modulated sheets with superior mechanical properties. The specific electrodeposition parameters were selected to produce ML samples with modulated grain size distribution and layer thicknesses varied from 30 nm up to 5 mu m. The influence of layer thickness on mechanical behavior was characterized by coupling nanoindentation tests and SEM/EDS study. Hardness results show that with decreasing layer thickness the strength of ML samples reaches a maximum value and remains relatively constant when layer thickness is less than 100 nm. The measured properties are discussed in the context of layer configuration, overall dimensions, and change in phase and chemical composition. (C) 2015 Elsevier Ltd. All rights reserved.
引用
收藏
页码：389 / 395
页数：7
相关论文
共 50 条
  • [31] Influence of Intermediate Annealing on the Nanostructure and Mechanical Properties of Pure Copper Processed by Equal Channel Angular Pressing and Cold Rolling
    Bahadori, Shahab Ranjbar
    Dehghani, Kamran
    METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2015, 46A (07): : 2796 - 2802
  • [32] Influence of process-induced microstructure and imperfections on mechanical properties of AlSi12 processed by selective laser melting
    Siddique, Shafaqat
    Imran, Muhammad
    Wycisk, Eric
    Emmelmann, Claus
    Walther, Frank
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2015, 221 : 205 - 213
  • [33] Influence of additives and plating parameters on morphology and mechanical properties of copper coatings obtained by pulse electrodeposition
    Imaz, N.
    Garcia-Lecina, E.
    Suarez, C.
    Diez, J. A.
    Rodriguez, J.
    Molina, J.
    Garcia-Navas, V.
    TRANSACTIONS OF THE INSTITUTE OF METAL FINISHING, 2009, 87 (02): : 64 - 71
  • [34] THE INFLUENCE OF GLUCONATE BATH PARAMETERS ON THE RATE OF ELECTRODEPOSITION AND MECHANICAL PROPERTIES OF Co-W COATINGS
    Belevskii, S. S.
    Bobanova, J., I
    Buravets, V. A.
    Gotelyak, A., V
    Danilchuk, V. V.
    Silkin, S. A.
    Tsyntsaru, N., I
    Dikusar, A., I
    PROCEEDINGS OF IX INTERNATIONAL SCIENTIFIC CONFERENCE (BALTTRIB 2017), 2018, : 7 - 12
  • [35] Multilayered Al/Ni energetic structural materials with high energy density and mechanical properties prepared by a facile approach of electrodeposition and hot pressing
    Wang, Mingzhi
    Qiu, Liangsheng
    Zhao, Xingjian
    Li, Yuanzhou
    Rao, Tianheng
    He, Shi
    Qin, Liang
    Tao, Jie
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2019, 757 : 23 - 31
  • [36] Through-thickness microstructure and mechanical properties in stationary shoulder friction stir processed AA7075
    Patel, Vivek
    Li, Wenya
    Liu, Xichang
    Wen, Quan
    Su, Yu
    MATERIALS SCIENCE AND TECHNOLOGY, 2019, 35 (14) : 1762 - 1769
  • [37] Influence of Layer Thickness on Cohesive Properties of an Epoxy-Based AdhesiveAn Experimental Study
    Carlberger, Thomas
    Stigh, Ulf
    JOURNAL OF ADHESION, 2010, 86 (08): : 814 - 833
  • [38] CuCrZr processed by laser powder bed fusion-Processability and influence of heat treatment on electrical conductivity, microstructure and mechanical properties
    Wegener, Thomas
    Koopmann, Julian
    Richter, Julia
    Krooss, Philipp
    Niendorf, Thomas
    FATIGUE & FRACTURE OF ENGINEERING MATERIALS & STRUCTURES, 2021, 44 (09) : 2570 - 2590
  • [39] Mechanical Properties and Damage Layer Thickness of Green Concrete under a Low-Temperature Environment
    Zhang, Dongsheng
    Zhang, Tianhao
    Yang, Qiuning
    MATERIALS, 2022, 15 (21)
  • [40] The mechanical properties of aged PA-12 FS3300PA powder: influence of layer thickness, sintering orientations, and laser power
    Rosley, Mohd Idain Fahmy
    Nuri, Nur Rashid Mat
    Nasir, Mohd Zakaria Mohammad
    Omar, Mohamad Rafi
    Mamat, Mohd Fauzi
    ENGINEERING RESEARCH EXPRESS, 2024, 6 (04):
12345