Optimization of process parameters in Electro Discharge Machining of AISI 304 stainless steel

被引：1

作者：

Behera, Asit ^{[1
]}

Panda, Debashrita ^{[1
]}

Bhadauriya, Mayank ^{[1
]}

机构：

[1] KIIT, SME, Bhubaneswar, Odisha, India

来源：

3RD INTERNATIONAL CONFERENCE ON MATERIALS AND MANUFACTURING ENGINEERING 2018 | 2018年 / 390卷

关键词：

EDM; Taguchi methodology; MRR; TAGUCHI METHOD; EDM;

D O I：

10.1088/1757-899X/390/1/012071

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Due to the profound use of AISI 304 stainless steel in household appliances optimization of process parameters in Electro Discharge Machining of AISI 304 is mostly needed for quality improvement. In this experiment AISI 304 stainless steel has been taken for machining with EDM oil dielectric. Three controllable parameters like peak current (Ip), pulse on time (Ton) and Flushing pressure (Fp) at three levels were taken for optimization. Material Removal Rate (MRR) was taken as response parameter and was measured for various combinations of controllable parameters. Taguchi optimization technique with L9 orthogonal array was used to optimize the specified controllable parameters. It was found that peak current of 15Amp, pulse on time of 200ms and Flushing pressure of 9Kgf/cm(2) bears the optimal quality characteristics. At these levels Material Removal Rate was found to be 16.250mm3/min.

引用

页数：6

共 50 条

[1] Optimization of Electro Discharge Machining Process Parameters With Fuzzy Logic for Stainless Steel 304 (ASTM A240)
Ubaid, Alaa M.
Dweiri, Fikri T.
Aghdeab, Shukry H.
Al-Juboori, Laith Abdullah
JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME, 2018, 140 (01):
[2] Optimization of Machining Parameters in Electrical Discharge Machining (EDM) of 304 Stainless Steel
Rajmohan, T.
Prabhu, R.
Rao, Subba G.
Palanikumar, K.
INTERNATIONAL CONFERENCE ON MODELLING OPTIMIZATION AND COMPUTING, 2012, 38 : 1030 - 1036
[3] Influence of Process Parameters on the Machining Characteristics of Austensite Stainless Steel (AISI 304)
Junaidh, A. P.
Yuvaraj, G.
Peter, Josephine
Bhuvaneshwari, V.
Kanagasabapathi
Karthik, K.
MATERIALS TODAY-PROCEEDINGS, 2018, 5 (05) : 13321 - 13333
[4] Optimization of Process Parameters on EDM Milling of Stainless Steel AISI 304
Iqbal, A. K. M. Asif
Khan, Ahsan Ali
ADVANCES IN MATERIALS AND PROCESSING TECHNOLOGIES II, PTS 1 AND 2, 2011, 264-265 : 979 - 984
[5] Investigation of the influential parameters of machining of AISI 304 stainless steel
R A MAHDAVINEJAD
S SAEEDY
Sadhana, 2011, 36 : 963 - 970
[6] Investigation of the influential parameters of machining of AISI 304 stainless steel
Mahdavinejad, R. A.
Saeedy, S.
SADHANA-ACADEMY PROCEEDINGS IN ENGINEERING SCIENCES, 2011, 36 (06): : 963 - 970
[7] Investigation on wire electrical discharge machining of AISI 304 stainless steel
Sen, Ruma
Paul, Subhodeep
Choudhuri, Bikash
MATERIALS TODAY-PROCEEDINGS, 2022, 62 : 1210 - 1214
[8] Optimization of Tungsten Inert Gas Welding Process Parameters for AISI 304 Stainless Steel
Baisukhan A.
Nakkiew W.
Wisittipanit N.
Defect and Diffusion Forum, 2022, 417 : 23 - 28
[9] Selection of Wire Electrical Discharge Machining Process Parameters on Stainless Steel AISI Grade-304 using Design of Experiments Approach
Lingadurai, K.
Nagasivamuni, B.
Muthu Kamatchi, M.
Palavesam, J.
Journal of The Institution of Engineers (India): Series C, 2012, 93 (02) : 163 - 170
[10] An experimental study of surface roughness in electrical discharge machining of AISI 304 stainless steel
Hernandez-Castillo, Ignacio
Sanchez-Lopez, Orquidea
Arturo Lancho-Romero, Guillermo
Hector Castaneda-Roldan, Cuauhtemoc
INGENIERIA E INVESTIGACION, 2018, 38 (02): : 90 - 96

← 1 2 3 4 5 →