Numerical Simulation of Desulfurization Behavior in Gas-Stirred Systems Based on Computation Fluid Dynamics-Simultaneous Reaction Model (CFD-SRM) Coupled Model

被引:75
作者
Lou, Wentao [1 ]
Zhu, Miaoyong [1 ]
机构
[1] Northeastern Univ, Sch Mat & Met, Shenyang 110819, Peoples R China
来源
METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE | 2014年 / 45卷 / 05期
基金
中国国家自然科学基金;
关键词
SLAG-METAL REACTIONS; SULFIDE CAPACITY; LIQUID-IRON; MOLTEN IRON; MASS-TRANSFER; OXYGEN ABSORPTION; SULFUR PARTITION; HOT METAL; LADLE; FURNACE;
D O I
10.1007/s11663-014-0105-0
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
A computation fluid dynamics-simultaneous reaction model (CFD-SRM) coupled model has been proposed to describe the desulfurization behavior in a gas-stirred ladle. For the desulfurization thermodynamics, different models were investigated to determine sulfide capacity and oxygen activity. For the desulfurization kinetic, the effect of bubbly plume flow, as well as oxygen absorption and oxidation reactions in slag eyes are considered. The thermodynamic and kinetic modification coefficients are proposed to fit the measured data, respectively. Finally, the effects of slag basicity and gas flow rate on the desulfurization efficiency are investigated. The results show that as the interfacial reactions (Al2O3)-(FeO)-(SiO2)-(MnO)-[S]-[O] simultaneous kinetic equilibrium is adopted to determine the oxygen activity, and the Young's model with the modification coefficient R (th) of 1.5 is adopted to determine slag sulfide capacity, the predicted sulfur distribution ratio LS agrees well with the measured data. With an increase of the gas blowing time, the predicted desulfurization rate gradually decreased, and when the modification parameter R (k) is 0.8, the predicted sulfur content changing with time in ladle agrees well with the measured data. If the oxygen absorption and oxidation reactions in slag eyes are not considered in this model, then the sulfur removal rate in the ladle would be overestimated, and this trend would become more obvious with an increase of the gas flow rate and decrease of the slag layer height. With the slag basicity increasing, the total desulfurization ratio increases; however, the total desulfurization ratio changes weakly as the slag basicity exceeds 7. With the increase of the gas flow rate, the desulfurization ratio first increases and then decreases. When the gas flow rate is 200 NL/min, the desulfurization ratio reaches a maximum value in an 80-ton gas-stirred ladle.
引用
收藏
页码:1706 / 1722
页数:17
相关论文
共 51 条
[1]   Slag-metal reactions during ladle treatment with focus on desulphurisation [J].
Andersson, M ;
Hallberg, M ;
Jonsson, L ;
Jönsson, P .
IRONMAKING & STEELMAKING, 2002, 29 (03) :224-232
[2]   Application of the sulphide capacity concept on high-basicity ladle slags used in bearing-steel production [J].
Andersson, MAT ;
Jönsson, PG ;
Nzotta, MM .
ISIJ INTERNATIONAL, 1999, 39 (11) :1140-1149
[3]   A thermodynamic and kinetic model of reoxidation and desulphurisation in the ladle furnace [J].
Andersson, MAT ;
Jonsson, LTI ;
Jonsson, PG .
ISIJ INTERNATIONAL, 2000, 40 (11) :1080-1088
[4]  
Ban-ya S., 1985, TETSU TO HAGANE, V71, P853
[5]   MATHEMATICAL EXPRESSION OF SLAG METAL REACTIONS IN STEELMAKING PROCESS BY QUADRATIC FORMALISM BASED ON THE REGULAR SOLUTION MODEL [J].
BANYA, S .
ISIJ INTERNATIONAL, 1993, 33 (01) :2-11
[6]  
BANYA S, 1985, T IRON STEEL I JPN, V25, P1122
[7]   Transient Kinetics of Slag Metal Reactions [J].
Brooks, G. A. ;
Rhamdhani, M. A. ;
Coley, K. S. ;
Subagyo ;
Pan, Y. .
METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE, 2009, 40 (03) :353-362
[8]   DIFFUSION OF MANGANESE AND SILICON IN LIQUID IRON OVER WHOLE RANGE OF COMPOSITION [J].
CALDERON, FP ;
SANO, N ;
MATSUSHI.Y .
METALLURGICAL TRANSACTIONS, 1971, 2 (12) :3325-&
[9]   THE SULFUR PARTITION RATIO AND THE SULFIDE CAPACITY OF NA2O-SIO2 SLAGS AT 1200-DEGREES-C [J].
CHAN, AH ;
FRUEHAN, RJ .
METALLURGICAL TRANSACTIONS B-PROCESS METALLURGY, 1986, 17 (03) :491-496
[10]  
Cheng J. X., 2010, COMMON USE HDB DIAGR, P840