Characterization of TiO2 Nanoparticle-Reinforced Polymer Nanocomposite Materials Printed by Stereolithography Method

被引:16
作者
Aktitiz, Ismail [1 ,2 ]
Aydin, Kadir [2 ]
Topcu, Alparslan [2 ]
机构
[1] Adana Alparslan Turkes Sci & Technol Univ, Fac Engn, Dept Mech Engn, TR-01250 Adana, Turkey
[2] Cukurova Univ, Fac Engn, Dept Mech Engn, TR-01330 Adana, Turkey
关键词
nanoparticle; nanocomposite; photosensitive resin; TiO2; stereolithography;
D O I
10.1007/s11665-021-05574-x
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
Additive manufacturing (AM) is a novel manufacturing technology group that revolutionizes the design and production processes behind material production. This approach is used in a wide range from simple prototypes to direct parts manufacturing in different industries such as aviation, automotive, energy, biomedical, and bioengineering. Stereolithography (SLA), fused deposition modeling, selective laser sintering, laser metal deposition approaches are the most widespread AM methods. SLA method is one of the most attractive approaches in the AM field as high-dimensional sensitivity is achieved by using liquid photosensitive resin and laser light. However, although it is possible to manufacture complex-shaped three-dimensional (3D) polymer structures with the SLA approach, the mechanical, thermal, and electrical properties are not at the desired levels. To develop more functional 3D polymer materials, various additives are dispersed into polymer structures such as metal nanoparticles, inorganic particles, fibre, carbon nanotube, and nanoclay. Titanium dioxide (TiO2) nanoparticles are a very appealing type of additive among these additives owing to their superior mechanical properties. In this study, the photosensitive resin was mixed with four different TiO2 nanoparticle concentrations (pure, 0.25, 0.5, and 1% reinforced). These slurries were then placed in the SLA device, and 3D polymer structures were fabricated. Scanning electron microscope (SEM), thermogravimetric analysis (TGA), differential scanning calorimeter (DSC), tensile tests, and Charpy impact tests were carried out to characterize mechanical, thermal, and morphological properties of developed polymer materials. It was observed that the particle size was below 1 mu m and some agglomerations occurred. The elasticity modulus of the 0.5% TiO2 nanoparticle reinforced sample was measured as 694 MPa and was found to be approximately 20% higher than the pure polymer sample. In addition, polymer structures exhibited more brittle behavior. It was noted that 5% weight loss was experienced at 337 degrees C in all samples. Besides, the existence of unreacted carbon-carbon bonds was proven by the DSC analysis.
引用
收藏
页码:4975 / 4980
页数:6
相关论文
共 37 条
[1]   In-situ synthesis of 3D printable mono- and Bi-metallic (Cu/Ag) nanoparticles embedded polymeric structures with enhanced electromechanical properties [J].
Aktitiz, Ismail ;
Varol, Remzi ;
Akkurt, Nevzat ;
Sarac, Mehmet Fahri .
POLYMER TESTING, 2020, 90
[2]  
[Anonymous], 2017, INDIAN J SCI TECHNOL, DOI DOI 10.17485/IJST/2017/V10I17/114413
[3]   Additive manufacturing of Ti-6Al-4V parts through laser metal deposition (LMD): Process, microstructure, and mechanical properties [J].
Azarniya, Abolfazl ;
Colera, Xabier Garmendia ;
Mirzaali, Mohammad J. ;
Sovizi, Saeed ;
Bartolomeu, Flavio ;
Weglowski, Marek St ;
Wits, Wessel W. ;
Yap, Chor Yen ;
Ahn, Joseph ;
Miranda, Georgina ;
Silva, Filipe Samuel ;
Hosseini, Hamid Reza Madaah ;
Ramakrishna, Seeram ;
Zadpoor, Amir A. .
JOURNAL OF ALLOYS AND COMPOUNDS, 2019, 804 :163-191
[4]   Stereolithography-based additive manufacturing of lithium disilicate glass ceramic for dental applications [J].
Baumgartner, Sonja ;
Gmeiner, Robert ;
Schoenherr, Julia Anna ;
Stampfl, Juergen .
MATERIALS SCIENCE AND ENGINEERING C-MATERIALS FOR BIOLOGICAL APPLICATIONS, 2020, 116
[5]   Stereolithography-based 3D printed photosensitive polymer/boron nitride nanoplatelets composites [J].
Bustillos, Jenniffer ;
Montero-Zambrano, Daniela ;
Loganathan, Archana ;
Boesl, Benjamin ;
Agarwal, Arvind .
POLYMER COMPOSITES, 2019, 40 (01) :379-388
[6]   Additive Manufacturing: Applications and Directions in Photonics and Optoelectronics [J].
Camposeo, Andrea ;
Persano, Luana ;
Farsari, Maria ;
Pisignano, Dario .
ADVANCED OPTICAL MATERIALS, 2019, 7 (01)
[7]   High performance polymer nanocomposites for additive manufacturing applications [J].
de Leon, Al C. ;
Chen, Qiyi ;
Palaganas, Napolabel B. ;
Palaganas, Jerome O. ;
Manapat, Jill ;
Advincula, Rigoberto C. .
REACTIVE & FUNCTIONAL POLYMERS, 2016, 103 :141-155
[8]   3D Stereolithography of Polymer Composites Reinforced with Orientated Nanoclay [J].
Eng, H. ;
Maleksaeedi, S. ;
Yu, S. ;
Choong, Y. Y. C. ;
Wiria, F. E. ;
Tan, C. L. C. ;
Su, P. C. ;
Wei, J. .
ICMAT 2017 SYMPOSIUM (M TO Z), 2017, 216 :1-7
[9]   Experimental investigation on bending behaviour of ZrO2 honeycomb sandwich structures prepared by DLP stereolithography [J].
Gao, Shuyue ;
Wang, Cao ;
Xing, Bohang ;
Shen, Minhao ;
Zhao, Weiming ;
Zhao, Zhe .
THIN-WALLED STRUCTURES, 2020, 157
[10]   Integration of Additive Manufacturing, Parametric Design, and Optimization of Parts Obtained by Fused Deposition Modeling (FDM). A Methodological Approach [J].
Garcia-Dominguez, Amabel ;
Claver, Juan ;
Sebastian, Miguel A. .
POLYMERS, 2020, 12 (09) :1-27