Experimental Study on The Influence of Parameters on The Plastic Parts Quality of External Gas-Assisted Injection Molding

被引：0
|
作者：
Jiang, Shaofei [1 ]
Zheng, Wei [1 ]
Zhang, Jiabo [1 ]
Li, Jiquan [1 ]
机构：
[1] Zhejiang Univ Technol, Minist Educ, Sch Mech Engn, Key Lab Special Purpose Equipment & Adv Proc Tech, Hangzhou 310014, Zhejiang, Peoples R China
来源：
APPLIED MATHEMATICS & INFORMATION SCIENCES | 2012年 / 6卷 / 03期
关键词：
EGAIM; parameters; single factor experiment; shrinkage;
D O I：
暂无
中图分类号：
O29 [应用数学];
学科分类号：
070104 ;
摘要：
External Gas-Assisted Injection Molding (EGAIM) is a kind of advanced plastic molding technology, which can reduce shrinkage defects of plastic products effectively. In this paper, the mold temperature, melt temperature, gas delay time, gas holding pressure, gas holding time and other parameters were studied respectively on the effects of plastic parts for quality in the molding process of EGAIM. Experimental studies by a single factor experiment on the interactions between parameters and plastic parts quality are as follows: mold temperature, melt temperature, gas delay time, gas holding pressure and gas holding time are the main factors in the parts' shrinkage.
引用
收藏
页码：665 / 671
页数：7
相关论文
共 50 条
  • [1] The influence of gas-assisted injection molding parameters on the structure and thermomechanical properties of hollow parts
    Gnatowski, Adam
    Stachowiak, Tomasz
    POLYMER ENGINEERING AND SCIENCE, 2013, 53 (02): : 257 - 262
  • [2] Experimental study of gas penetration in gas-assisted injection molding
    Shin, Jin-Woong
    Isayev, A.I.
    Journal of Injection Molding Technology, 2002, 6 (04): : 314 - 330
  • [3] Study on gas penetration in gas-assisted injection molding of thin wall parts
    Xin, Yong
    Peng, Yinghong
    Ruan, Xueyu
    Zhongguo Jixie Gongcheng/China Mechanical Engineering, 2003, 14 (08):
  • [4] Reducing the Burn Marks on Injection-Molded Parts by External Gas-Assisted Injection Molding
    Li, Jiquan
    Liu, Wenyong
    Xia, Xinxin
    Zhou, Hangchao
    Jing, Liting
    Peng, Xiang
    Jiang, Shaofei
    POLYMERS, 2021, 13 (23)
  • [5] Cooling Simulation of External Gas-assisted Injection Molding
    Jiang, ShaoFei
    Zhang, JiaBo
    Chai, GuoZhong
    Li, JiQuan
    Su, MaoYing
    FRONTIERS OF MANUFACTURING AND DESIGN SCIENCE, PTS 1-4, 2011, 44-47 : 1607 - 1611
  • [6] An experimental study to investigate the influence of processing conditions in the gas-assisted injection molding process
    Kapila, V
    Schott, NR
    Shah, S
    ANTEC '96: PLASTICS - RACING INTO THE FUTURE, VOLS I-III: VOL I: PROCESSING; VOL II: MATERIALS; VOL III: SPACIAL AREAS, 1996, 42 : 649 - 654
  • [7] Gas-assisted injection molding
    Anon
    Modern Plastics, 1990, 67 (06):
  • [8] Effect of gas on the polymer temperature in external gas-assisted injection molding
    Li, Taidong
    Li, Jiquan
    Desplentere, Frederik
    Xia, Xinxin
    Peng, Xiang
    Jiang, Shaofei
    JOURNAL OF POLYMER ENGINEERING, 2019, 39 (06) : 587 - 595
  • [9] Parameters affecting the full-shot molding of gas-assisted injection-molded parts
    Liu, SJ
    Chang, KH
    ADVANCES IN POLYMER TECHNOLOGY, 2003, 22 (01) : 1 - 14
  • [10] Study on the Packing Effects of External Gas-Assisted Injection Molding on Part Shrinkage in Comparison With Conventional Injection Molding
    Chen, Shia-Chung
    Lin, Yi-Chang
    Huang, Sung-Wei
    POLYMER ENGINEERING AND SCIENCE, 2010, 50 (11): : 2085 - 2092
12345