Synthesis and characterization of zinc oxide (ZnO) filled glass fiber reinforced polyester composites

被引：47

作者：

Gull, Nafisa ^{[1
]}

Khan, Shahzad Maqsood ^{[1
]}

Munawar, Muhammad Azeem ^{[1
]}

Shafiq, Muhammad ^{[1
]}

Anjum, Farheen ^{[1
]}

Butt, Muhammad Taqi Zahid ^{[2
]}

Jamil, Tahir ^{[1
]}

机构：

[1] Univ Punjab, Dept Polymer Engn & Technol, Lahore, Pakistan

[2] Univ Punjab, Coll Engn & Emerging Technol, Lahore, Pakistan

来源：

MATERIALS & DESIGN | 2015年 / 67卷

关键词：

MECHANICAL-PROPERTIES; WEAR; PARTICLES; BEHAVIOR;

D O I：

10.1016/j.matdes.2014.11.021

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

This study aims at fabrication of zinc oxide (ZnO) filled glass fiber reinforced polyester (GFRP) composites with varying concentrations of filler and investigation of their mechanical and thermal behavior. In this study, ZnO was dispersed in polyester, and laminates were fabricated by hand lay-up technique followed by compression molding. Mechanical properties were determined by flexural strength analysis, impact strength and hardness testing whereas thermal stability by thermogravimetric analysis (TGA). Flexural strength of 3 wt.% ZnO filled GFRP composite was improved significantly (up to 62.12%) in comparison to unfilled composite. Hardness, impact strength and thermal stability have also been found increased gradually with increase in ZnO loading. (C) 2014 Elsevier Ltd. All rights reserved.

引用

页码：313 / 317

页数：5

共 42 条

[1]

Agarwal Gaurav, 2013, International Journal of Advanced Structural Engineering, V5, DOI 10.1186/2008-6695-5-21

[2]

[Anonymous], PUBLIC LECT SER

[3] Mechanical and wear behaviours of nano and microfilled polymeric composite: Effect of filler fraction and size [J].

Antunes, P. V. ;

Ramalho, A. ;

Carrilho, E. V. P. .

MATERIALS & DESIGN, 2014, 61 :50-60

[4] THERMAL-STABILITY AND DEGRADATION STUDIES OF POLYESTER RESINS [J].

BANSAL, RK ;

MITTAL, J ;

SINGH, P .

JOURNAL OF APPLIED POLYMER SCIENCE, 1989, 37 (07) :1901-1908

[5] Statistical effects of using ceramic particles in glass fibre reinforced composites [J].

Detomi, Anine Cristina ;

dos Santos, Reniene Maria ;

Ribeiro Filho, Sergio Luiz Moni ;

Martuscelli, Carolina Coelho ;

Panzera, Tulio Hallak ;

Scarpa, Fabrizio .

MATERIALS & DESIGN, 2014, 55 :463-470

[6]

Devendra K., 2012, International Journal of Computational Engineering Research, V2, P1708

[7]

Devendra T., 2013, J. Miner. Mater. Charact. Eng., V1, P353, DOI [10.4236/jmmce.2013.16054, DOI 10.4236/JMMCE.2013.16054]

[8] FRICTION AND WEAR PROPERTIES OF POLYMERIC COMPOSITE-MATERIALS FOR BEARING APPLICATIONS [J].

ELSAYED, AA ;

ELSHERBINY, MG ;

ABOELEZZ, AS ;

AGGAG, GA .

WEAR, 1995, 184 (01) :45-53

[9] Effects of particle size, particle/matrix interface adhesion and particle loading on mechanical properties of particulate-polymer composites [J].

Fu, Shao-Yun ;

Feng, Xi-Qiao ;

Lauke, Bernd ;

Mai, Yiu-Wing .

COMPOSITES PART B-ENGINEERING, 2008, 39 (06) :933-961

[10] Influence of calcium carbonate on RTM and RTM light processing and properties of molded composites [J].

Garay, Andre C. ;

Heck, Vicente ;

Zattera, Ademir J. ;

Souza, Jeferson A. ;

Amico, Sandro C. .

JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 2011, 30 (14) :1213-1221

← 1 2 3 4 5 →