Tuning composition and microstructure by doping Ti and C for enhancing mechanical property and wear resistance of Al0.2Co1.5CrFeNi1.5Ti0.5 high entropy alloy matrix composites

被引：52
作者：
Xin, Benbin [1 ,2 ]
Zhang, Aijun [1 ]
Han, Jiesheng [1 ]
Su, Bo [1 ]
Meng, Junhu [1 ]
机构：
[1] Chinese Acad Sci, Lanzhou Inst Chem Phys, State Key Lab Solid Lubricat, Lanzhou 730000, Peoples R China
[2] Univ Chinese Acad Sci, Ctr Mat Sci & Optoelect Engn, Beijing 100049, Peoples R China
来源：
JOURNAL OF ALLOYS AND COMPOUNDS | 2020年 / 836卷
关键词：
High entropy alloy matrix composites; In situ reaction; Mechanical properties; Tribological properties; Tribo-chemical reaction; EVOLUTION; BEHAVIOR; CARBON; COATINGS; HARDNESS; PERFORMANCE; STRENGTH; FRICTION; STEEL;
D O I：
10.1016/j.jallcom.2020.155273
中图分类号：
O64 [物理化学（理论化学）、化学物理学];
学科分类号：
070304 ; 081704 ;
摘要：
Spark plasma sintering was used to prepare in-situ synthesized TiC reinforced Al0.2Co1.5CrFeNi1.5Ti0.5 high entropy alloy matrix composites with adding Ti and C elements by the molar ratio of 1:1. Face-centered cubic (FCC) solid solution and in-situ synthesized TiC were the main components of the composite. The content of nanocrystals which induced by grain boundary pinning effect of TiC increased with increasing of Ti and C content. The micro Vickers hardness increased from 410 HV0.3 to 850 HV0.3 and the yield strength increased from 1080 MPa to 2164 MPa when the C content increase to the molar ratio of 2.0. Interstitial solution strengthening, dispersion strengthening, grain-boundary strengthening and fine grain strengthening were the main strengthening mechanisms for the in-situ TiC enhanced Al0.2Co1.5CrFeNi1.5Ti0.5 high entropy alloy matrix composites. The wear resistance of Al0.2Co1.5CrFeNi1.5Ti2.5C2.0 composite was about 40 times higher than that of Al0.2Ca1.5CrFeNi1.5Ti0.5 high entropy alloy. The reinforcing effect of TiC and the protective effect of TiO2 oxide glaze layer which formed by the in-situ tribo-chemical reaction during the friction process were the main reasons for the improvement of wear resistance. (C) 2020 Elsevier B.V. All rights reserved.
引用
收藏
页数：13
相关论文
共 44 条
  • [31] Diffusion rate of carbon in iron-cobalt alloys
    Smoluchowski, R
    [J]. PHYSICAL REVIEW, 1942, 62 (11/12): : 539 - 544
  • [32] In situ fabrication of TiC particulates locally reinforced aluminum matrix composites by self-propagating reaction during casting
    Song, M. S.
    Zhang, M. X.
    Zhang, S. G.
    Huang, B.
    Li, J. G.
    [J]. MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2008, 473 (1-2): : 166 - 171
  • [33] The effect of surface texturing on reducing the friction and wear of steel under lubricated sliding contact
    Tang, Wei
    Zhou, Yuankai
    Zhu, Hua
    Yang, Haifeng
    [J]. APPLIED SURFACE SCIENCE, 2013, 273 : 199 - 204
  • [34] Microstructure characterization of AlxCoCrCuFeNi high-entropy alloy system with multiprincipal elements
    Tong, CJ
    Chen, YL
    Chen, SK
    Yeh, JW
    Shun, TT
    Tsau, CH
    Lin, SJ
    Chang, SY
    [J]. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2005, 36A (04): : 881 - 893
  • [35] Al-TiC composites in situ processed by ingot metallurgy and rapid solidification technology: Part I. Microstructural evolution
    Tong, XC
    Fang, HS
    [J]. METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 1998, 29 (03): : 875 - 891
  • [36] The effect of interstitial carbon on the mechanical properties and dislocation substructure evolution in Fe40.4Ni11.3Mn34.8Al7.5Cr6 high entropy alloys
    Wang, Zhangwei
    Baker, Ian
    Cai, Zhonghou
    Chen, Si
    Poplawsky, Jonathan D.
    Guo, Wei
    [J]. ACTA MATERIALIA, 2016, 120 : 228 - 239
  • [37] Effect of lattice distortion on solid solution strengthening of BCC high-entropy alloys
    Wang, Zhipeng
    Fang, Qihong
    Li, Jia
    Liu, Bin
    Liu, Yong
    [J]. JOURNAL OF MATERIALS SCIENCE & TECHNOLOGY, 2018, 34 (02) : 349 - 354
  • [38] Microstructure and wear property of the Ti5Si3/TiC reinforced Co-based coatings fabricated by laser cladding on Ti-6A1-4V
    Weng, Fei
    Yu, Huijun
    Liu, Jianli
    Chen, Chuanzhong
    Dai, Jingjie
    Zhao, Zhihuan
    [J]. OPTICS AND LASER TECHNOLOGY, 2017, 92 : 156 - 162
  • [39] Microstructural evolution of subsurface on Inconel 690TT alloy subjected to fretting wear at elevated temperature
    Xin, L.
    Yang, B. B.
    Wang, Z. H.
    Li, J.
    Lu, Y. H.
    Shoji, T.
    [J]. MATERIALS & DESIGN, 2016, 104 : 152 - 161
  • [40] Effect of different strengthening methods on rolling/sliding wear of ferrite-pearlite steel
    Zeng, Dongfang
    Lu, Liantao
    Zhang, Ning
    Gong, Yubin
    Zhang, Jiwang
    [J]. WEAR, 2016, 358-359 : 62 - 71
12345