Effect of hot extrusion and subsequent T6 treatment on the microstructure evolution and tensile properties of an Al-6Si-2Cu-0.5Mg alloy

被引：24
|
作者：
Xu, Cong [1 ]
Zheng, Ruixiao [1 ]
Hanada, Shuji [2 ]
Xiao, Wenlong [1 ]
Ma, Chaoli [1 ]
机构：
[1] Beihang Univ, Sch Mat Sci & Engn, Minist Educ, Key Lab Aerosp Adv Mat & Performance, Beijing 100191, Peoples R China
[2] Tohoku Univ, Inst Mat Res, Sendai 9808577, Japan
来源：
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2018年 / 710卷
基金：
中国国家自然科学基金;
关键词：
Al-6Si-2Cu-0.5Mg alloy; Extrusion temperature; Microstructure; Strength; Ductility; MECHANICAL-PROPERTIES; HEAT-TREATMENT; COOLING RATE; MG; CU; PARTICLES; BEHAVIOR; ELEMENTS; COPPER; PHASE;
D O I：
10.1016/j.msea.2017.10.052
中图分类号：
TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
In this work, an Al-6Si-2Cu-0.5Mg alloy was subjected to hot extrusion at various temperatures (400 degrees C, 450 degrees C and 500 degrees C) followed by subsequent T6 heat treatment, and the effect of aforementioned thermal-mechanical treatment on the microstructure evolution and tensile properties was systematically investigated. Microstructure observed suggested that both eutectic Si particles and primary intermetallic particles (Q phase) were refined by hot extrusion. Further T6 treatment led to the dissolution of the Q phase and the formation of nano-precipitates. Tensile test revealed that the alloy extruded at 450 degrees C (after T6 treatment) exhibited the best combination of strength and ductility. Increasing or decreasing the extrusion temperature resulted in the deterioration of ductility. The effect of the extrusion temperature and T6 treatment on the mechanical properties was discussed based on the microstructure evolution.
引用
收藏
页码：102 / 110
页数：9
相关论文
共 50 条
  • [21] Effect of short T6 heat treatment on the microstructure and the mechanical properties of newly developed die-cast Al-Si-Mg-Mn alloys
    Cai, Qing
    Mendis, Chamini L.
    Chang, Isaac T. H.
    Fan, Zhongyun
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2020, 788
  • [22] Effect of T6 Heat Treatment on the Microstructural and Mechanical Properties of Al-Si-Cu-Mg Alloys
    Patel, Dhruv
    Davda, Chintan
    Solanki, P. S.
    Keshvani, M. J.
    INTERNATIONAL CONFERENCE ON CONDENSED MATTER AND APPLIED PHYSICS (ICC 2015), 2016, 1728
  • [23] The simultaneous effect of extrusion and T6 treatment on the mechanical properties of Al-15wt.% Mg2Si composite
    Soltani, N.
    Bahrami, A.
    Moghimi, F. M.
    Pech-Canul, M. I.
    Hajaghasi, A.
    HTM-JOURNAL OF HEAT TREATMENT AND MATERIALS, 2012, 67 (06): : 378 - 385
  • [24] Effect of Heat Treatment Parameters on Properties of Al-4.8Si-1.2Cu-0.5Mg Alloy
    Shi, Dequan
    Kang, Kaijiao
    Du, Zhimin
    Li, Dayong
    Gao, Guili
    Xu, Zhenyu
    MATERIALS TRANSACTIONS, 2020, 61 (07) : 1315 - 1321
  • [25] EFFECTS OF T6 HEAT TREATMENT WITH DOUBLE SOLUTION TREATMENT ON MICROSTRUCTURE, HARDNESS AND CORROSION RESISTANCE OF CAST Al-Si-Cu ALLOY
    Wiengmoon, A.
    Sukchot, P.
    Tareelap, N.
    Pearce, J. T. H.
    Chairuangsri, T.
    ARCHIVES OF METALLURGY AND MATERIALS, 2015, 60 (02) : 881 - 886
  • [26] Effects of T6 Age Hardening on Microstructure and Mechanical Properties of Al-Si-Cu Cast Aluminium Alloy
    Wiengmoon, Amporn
    Apichai, Pattama
    Pearce, John T. H.
    Chairuangsri, Torranin
    APPLIED PHYSICS AND MATERIAL APPLICATIONS, 2013, 770 : 88 - +
  • [27] A comparative study of the tribological properties of as cast and 3Hr T6 treated Al-25Mg2Si2Cu4Fe alloy
    Sondur, D. G.
    Mallapur, D. G.
    MATERIALS TODAY-PROCEEDINGS, 2017, 4 (10) : 11023 - 11027
  • [28] Surface hardening of an Al-Si-Cu-Ni-Mg aluminum alloy by friction stir processing and T6 heat treatment
    Khalikova, G. R.
    Zakirova, G. R.
    Farkhutdinov, A., I
    Korznikova, E. A.
    Trifonov, V. G.
    LETTERS ON MATERIALS, 2022, 12 (03): : 255 - 260
  • [29] Microstructure and Tensile Properties of Al-15wt%Mg2Si Composite after Hot Extrusion and Heat Treatment
    Bahrami, A.
    Razaghian, A.
    Emamy, M.
    Jafari, H. R.
    Mousavi, G. S.
    COMPOSITE SCIENCE AND TECHNOLOGY, PTS 1 AND 2, 2011, 471-472 : 1171 - +
  • [30] Effects of Cu content on microstructure and mechanical properties of Al-14.5Si-0.5Mg alloy
    Wu, Chih-Ting
    Lee, Sheng-Long
    Hsieh, Meng-Hsiung
    Lin, Jing-Chie
    MATERIALS CHARACTERIZATION, 2010, 61 (11) : 1074 - 1079
12345