INFLUENCE OF THE TOOL RAKE ANGLE ON RESIDUAL STRESSES IN CASE OF ORTHOGONAL HARD TURNING OF AISI 5115 CASE HARDENED STEEL

被引：0
|
作者：
Szabo, G. [1 ]
机构：
[1] Univ Miskolc, Dept Prod Engn, H-3515 Miskolc, Hungary
来源：
13TH INTERNATIONAL CONFERENCE ON TOOLS | 2012年
关键词：
hard turning; tool rake angle; residual stress;
D O I：
暂无
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
With the technological conditions and cutting edge geometry chosen acceptably, the mechanical properties of the machined surface layer can be improved significantly. The appropriate cutting edge geometry plays an important role in the hard turning technology. The paper is about the analysis of the state of residual stress depending on the change of rake angle in orthogonal hard turning of case hardened steel signed by AISI 5115.
引用
收藏
页码：77 / 82
页数：6
相关论文
共 50 条
  • [31] Effect of cutting-edge geometry and workpiece hardness on surface residual stresses in finish hard turning of AISI 52100 steel
    Thiele, Jeffrey D.
    Melkote, Shreyes N.
    Peascoe, Roberta A.
    Watkins, Thomas R.
    American Society of Mechanical Engineers, Manufacturing Engineering Division, MED, 1999, 10 : 797 - 805
  • [32] Effect of cutting-edge geometry and workpiece hardness on surface residual stresses in finish hard turning of AISI 52100 steel
    Thiele, JD
    Melkote, SN
    Peascoe, RA
    Watkins, TR
    JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME, 2000, 122 (04): : 642 - 649
  • [33] MODELING AND EXPERIMENTAL VALIDATION OF THE SURFACE RESIDUAL STRESSES INDUCED BY HARD MACHINING OF AISI H13 TOOL STEEL
    Caruso, S.
    Outeiro, J. C.
    Umbrello, D.
    M'Saoubi, R.
    INTERNATIONAL JOURNAL OF MATERIAL FORMING, 2010, 3 : 515 - 518
  • [34] Modeling and experimental validation of the surface residual stresses induced by hard machining of AISI H13 tool steel
    S. Caruso
    J. C. Outeiro
    D. Umbrello
    R. M’Saoubi
    International Journal of Material Forming, 2010, 3 : 515 - 518
  • [35] Electro-discharge machining (EDM) versus hard turning and grinding -: Comparison of residual stresses and surface integrity generated in AISI O1 tool steel
    Garcia Navas, V.
    Ferreres, I.
    Maranon, J. A.
    Garcia-Rosales, C.
    Gil Sevillano, J.
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2008, 195 (1-3) : 186 - 194
  • [36] Experimental investigation and analysis of the influence of tool edge geometry and work piece hardness on surface residual stresses, surface roughness and work-hardening in hard turning of AISI D2 steel
    Sarnobat, S. S.
    Raval, H. K.
    MEASUREMENT, 2019, 131 : 235 - 260
  • [37] Effects of process variables on the case depth of laser transformation hardened AISI 01 tool steel specimens
    Yang, L.J.
    Jana, S.
    Tam, S.C.
    Lim, L.E.N.
    Materials and Manufacturing Processes, 1994, 9 (03) : 475 - 492
  • [38] DISCUSSION OF INFLUENCE OF RESIDUAL AUSTENITE ON MECHANICAL PROPERTIES OF CASE HARDENED SPECIMENS SUBJECTED TO ALTERNATING STRESSES
    RADEMACH.L
    RAZIM, C
    ROSE, A
    SCHAABER, O
    LAPCZINS.M
    HAMMER, K
    LIEDTKE, D
    REVUE DE METALLURGIE-CAHIERS D INFORMATIONS TECHNIQUES, 1969, 66 (02): : 157 - &
  • [39] Influence of residual stresses and mean load on the fatigue strength of case-hardened notched specimens
    Krug, Thomas
    Lang, Karl-Heinz
    Fett, Theo
    Loehe, Detlef
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2007, 468 : 158 - 163
  • [40] Effect of cutting parameters on surface roughness using orthogonal array in hard turning of AISI 1045 steel with YT5 tool
    Xiao, Zeqing
    Liao, Xiaoping
    Long, Zhenhong
    Li, Ming
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2017, 93 (1-4): : 273 - 282
12345