Residual stresses in glass after molding and its influence on optical properties

被引：21
|
作者：
Yi, A. Y. [1 ]
Tao, B. [1 ]
Klocke, F. [2 ]
Dambon, O. [2 ]
Wang, F. [2 ]
机构：
[1] Ohio State Univ, Dept Integrated Syst Engn, 210 Baker Syst,1971 Neal Ave, Columbus, OH 43210 USA
[2] Fraunhofer Inst Prod Technol, D-54004 Aachen, Germany
来源：
1ST CIRP CONFERENCE ON SURFACE INTEGRITY (CSI) | 2011年 / 19卷
关键词：
Glass; Residual Stress; Finite Element Method (FEM); Optical;
D O I：
10.1016/j.proeng.2011.11.132
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
Compression molding of glass optics is gradually becoming a viable manufacturing process for high precision optical lenses. However, during cooling, glass properties undergo a small amount of changes due to structural relaxation. As a result, residual stresses are trapped inside the molded glass lenses. In this research, compression molded lenses were studied using the birefringence method assisted by the finite element analysis. The experimental and simulation results showed that compression molding process can be controlled to a very high precision providing that the proper cooling is applied during cooling. In addition, numerical analysis using finite element analysis also provides a better understand of the cooling process and offers an economic solution for process optimization for low cost glass lens production. (C) 2012 Published by Elsevier Ltd. Selection and peer-review under responsibility of Prof. E. Brinksmeier
引用
收藏
页数：5
相关论文
共 50 条
  • [1] Numerical Simulation and Experimental Study of Residual Stresses in Compression Molding of Precision Glass Optical Components
    Chen, Yang
    Yi, Allen Y.
    Su, Lijuan
    Klocke, Fritz
    Pongs, Guido
    JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME, 2008, 130 (05): : 0510121 - 0510129
  • [2] Internal residual stresses in glass-ceramics: A review
    Serbena, Francisco C.
    Zanotto, Edgar D.
    JOURNAL OF NON-CRYSTALLINE SOLIDS, 2012, 358 (6-7) : 975 - 984
  • [3] Numerical and experimental investigations on the residual stresses at the centre of flat glass disks after thermal tempering
    Soulie, Frederic
    Siedow, Norbert
    Anton, John
    Lochegnies, Dominique
    GLASS - THE CHALLENGE FOR THE 21ST CENTURY, 2008, 39-40 : 553 - +
  • [4] Numerical Simulations of Residual Stresses and Warpage in Injection Molding
    Liu, Fen
    Zhou, Huamin
    Li, Dequin
    JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 2009, 28 (05) : 571 - 585
  • [5] Visualizing Residual Stresses in Plastic and Glass
    Maciejewski J.
    Journal of Failure Analysis and Prevention, 2017, 17 (1) : 5 - 7
  • [6] Residual Structural Stresses in Glass Bodies
    Budz, S. F.
    Drobenko, B. D.
    Astashkin, V. I.
    MATERIALS SCIENCE, 2014, 50 (03) : 406 - 411
  • [7] Residual Structural Stresses in Glass Bodies
    S. F. Budz
    B. D. Drobenko
    V. I. Astashkin
    Materials Science, 2014, 50 : 406 - 411
  • [8] Influence of thermal properties on residual stresses in SLM of aerospace alloys
    Yakout, Mostafa
    Elbestawi, M. A.
    Veldhuis, S. C.
    Nangle-Smith, S.
    RAPID PROTOTYPING JOURNAL, 2020, 26 (01) : 213 - 222
  • [9] Thermoformed glass fiber reinforced polypropylene: Microstructure, mechanical properties and residual stresses
    Youssef, Y
    Denault, J
    EVOLVING TECHNOLOGIES FOR THE COMPETITIVE EDGE, BOOKS 1 AND 2, 1997, 42 : 134 - 146
  • [10] Study on residual stresses of thin-walled injection molding
    Wang, TH
    Young, WB
    EUROPEAN POLYMER JOURNAL, 2005, 41 (10) : 2511 - 2517
12345