Modeling permanent mold casting of aluminum

被引：0

作者：

Cook, Daniel P. ^{[1
]}

Deshmukh, Sachin S. ^{[1
]}

Carey, David P. ^{[1
]}

机构：

[1] Univ Nevada, Dept Mech Engn, Las Vegas, NV 89154 USA

来源：

PROCEEDINGS OF THE ASME INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION 2007, VOL 8, PTS A AND B: HEAT TRANSFER, FLUID FLOWS, AND THERMAL SYSTEMS | 2008年

关键词：

D O I：

暂无

中图分类号：

O414.1 [热力学];

学科分类号：

摘要：

Modeling the complex, coupled fluid flow, heat transfer and solidification phenomena taking place in metal casting is a challenging task. The quality of any metal casting depends on many parameters such as the type of mould, rate of filling, and rate of solidification. Optimization of these operational parameters is very important in reducing casting defects such as oxide inclusions and porosity. This paper addresses the first steps in validating a computational fluid dynamics (CFD) model of permanent mold casting of aluminum. A mathematical model of the casting system has been developed using the commercial CFD package StarCD. A physical model of the system has been used to validate the mold filling phenomena in the process. Comparison of the results from these models will be presented.

引用

页码：1825 / 1828

页数：4

共 50 条

[31] MOLD FOR CASTING ALUMINUM SPECTROGRAPHIC STANDARDS [J].

REDFIELD, HL ;

WAGONER, WS .

ANALYTICAL CHEMISTRY, 1973, 45 (01) :140-144

[32] LOW-PRESSURE PERMANENT-MOLD PROCESS SIMULATION OF A THIN WALL ALUMINUM CASTING [J].

KREZIAK, G ;

RIGAUT, C ;

SANTARINI, M .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1993, 173 (1-2) :255-259

[33] Interfacial Heat Transfer Coefficient in Unidirectional Permanent Mold Casting: Modeling and Inverse Estimation [J].

Stieven, Gianfranco de M. ;

Soares, Daniele dos R. ;

Oliveira, Edilma P. ;

Lins, Erb F. .

International Journal of Heat and Mass Transfer, 2021, 166

[34] Interfacial Heat Transfer Coefficient in Unidirectional Permanent Mold Casting: Modeling and Inverse Estimation [J].

Stieven, Gianfranco de M. ;

Soares, Daniele dos R. ;

Oliveira, Edilma R. ;

Lins, Erb F. .

INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2021, 166

[35] Designing aluminum permanent mold castings [J].

Metal Casting Design and Purchasing, 2019, 21 (04) :28-31

[36] Effect of mold coating on thermal fatigue in Al permanent mold casting [J].

Martinez, KM ;

Ramsay, CW ;

Askeland, DR .

TRANSACTIONS OF THE AMERICAN FOUNDRYMEN'S SOCIETY, VOL 106, 1998, 106 :207-213

[37] Influence of Mold Coating on Heat Transport in Permanent Mold Casting Process [J].

Wet, S. ;

Dillingham, J. ;

Jiranek, M. R. ;

Nyamekye, K. .

Transactions of the American Foundrymen's Society, (104)

[38] Production of Aluminum Cylinders for Small Two-Stroke Engines by Low Pressure Permanent Mold Casting and by Die Casting. [J].

Asbeck, Otto ;

Wacker, Erich .

Giesserei, 1973, 60 (10) :282-290

[39] Helium-Enhanced Semi-Permanent Mold Aluminum Casting (12-13#05) [J].

Sanders, Paul ;

Metzloff, Kyle .

INTERNATIONAL JOURNAL OF METALCASTING, 2016, 10 (01) :122-123

[40] Helium-Enhanced Semi-Permanent Mold Aluminum Casting (12-13#05) [J].

Sanders, Paul ;

Metzloff, Kyle ;

Began, Brian .

INTERNATIONAL JOURNAL OF METALCASTING, 2016, 10 (02) :224-225

← 1 2 3 4 5 →