Influence of tool wear on residual stresses when turning Inconel 718

被引：26

作者：

Madariaga, A. ^{[1
]}

Kortabarria, A. ^{[1
]}

Hormaetxe, E. ^{[1
]}

Garay, A. ^{[1
]}

Arrazola, P. J. ^{[1
]}

机构：

[1] Mondragon Uniberstitatea, Fac Engn, Loramendi 4, Arrasate Mondragon 20500, Spain

来源：

3RD CIRP CONFERENCE ON SURFACE INTEGRITY | 2016年 / 45卷

关键词：

Residual Stress; Turning; Wear; SURFACE INTEGRITY; NOSE RADIUS;

D O I：

10.1016/j.procir.2016.02.359

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

This paper analyzes the effect of tool wear on residual stresses when turning. Inconel 718 discs were machined for prolonged periods at several cutting speeds, feed-rates and depth of cut. Tests were interrupted to measure and relate tool wear with the subsequent residual stress measurements. The discussion of experimental results is supported by orthogonal cutting simulations. It was found a critical tool wear where tensile surface residual stresses were maximum, decreasing for lower and higher values of tool wear. Nevertheless, it was observed that the compressive residual stress layer increased with increasing tool wear. (C) 2016 The Authors. Published by Elsevier B.V.

引用

页码：267 / 270

页数：4

共 13 条

[1]

EEBB Departament of Defense, 1998, MIL HDB MIL HDBK 5H

[2] Surface integrity of die material in high speed hard machining, part 2: Microhardness variations and residual stresses [J].

El-Wardany, TI ;

Kishawy, HA ;

Elbestawi, MA .

JOURNAL OF MANUFACTURING SCIENCE AND ENGINEERING-TRANSACTIONS OF THE ASME, 2000, 122 (04) :632-641

[3] Application of fine increment hole drilling for measuring machining-induced residual stresses [J].

Grant, P. ;

Lord, J. ;

Whitehead, P. ;

Fry, T. .

Advances in Experimental Mechanics IV, 2005, 3-4 :105-110

[4] Effect of tool nose radius and tool wear on residual stress distribution in hard turning of bearing steel [J].

Liu, M ;

Takagi, J ;

Tsukuda, A .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2004, 150 (03) :234-241

[5] Analysis of residual stress and work-hardened profiles on Inconel 718 when face turning with large-nose radius tools [J].

Madariaga, A. ;

Esnaola, J. A. ;

Fernandez, E. ;

Arrazola, P. J. ;

Garay, A. ;

Morel, F. .

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2014, 71 (9-12) :1587-1598

[6] Thermomechanical finite element simulations of ultrasonically assisted turning [J].

Mitrofanov, AV ;

Babitsky, VI ;

Silberschmidt, VV .

COMPUTATIONAL MATERIALS SCIENCE, 2005, 32 (3-4) :463-471

[7] Numerical analysis of the tool wear effect in the machining induced residual stresses [J].

Munoz-Sanchez, A. ;

Canteli, J. A. ;

Cantero, J. L. ;

Miguelez, M. H. .

SIMULATION MODELLING PRACTICE AND THEORY, 2011, 19 (02) :872-886

[8]

Oettel R., 2000, COD OF PRACT, V15

[9] Prediction of residual stress distribution after turning in turbine disks [J].

Salio, M. ;

Berruti, T. ;

De Poli, G. .

INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES, 2006, 48 (09) :976-984

[10] The effect of tool nose radius on surface integrity and residual stresses when turning Inconel 718™ [J].

Sharman, A. R. C. ;

Hughes, J. I. ;

Ridgway, K. .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2015, 216 :123-132

← 1 2 →