Performance characteristics of the direct spray oil cooling system for a driving motor of an electric vehicle

被引：36
作者：
Garud, Kunal Sandip [1 ]
Hwang, Seong-Guk [1 ]
Han, Jeong-Woo [1 ]
Lee, Moo-Yeon [1 ]
机构：
[1] Dong A Univ, Dept Mech Engn, 37 Nakdong Daero 550, Busan, South Korea
来源：
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER | 2022年 / 196卷
关键词：
Direct spray oil cooling system; Heat transfer coefficient; Nusselt number; Spray resistance; Spray power consumption; Electric vehicle driving motor; HEAT-TRANSFER PERFORMANCE; NUMERICAL-SIMULATION; NOZZLE; INCLINATION; ATOMIZATION;
D O I：
10.1016/j.ijheatmasstransfer.2022.123228
中图分类号：
O414.1 [热力学];
学科分类号：
摘要：
In the present work, the performance characteristics of direct spray oil cooling system with spiral, and two full cone nozzles and three cooling oils of mineral oil, dielectric oil and transmission oil are ex-perimentally investigated. The temperature, temperature uniformity, injection pressure, spray resistance, heat transfer coefficient, Nusselt number and spray power consumption are evaluated as the performance characteristics of direct spray oil cooling system. The influences of heating capacities of 1.3 kW and 2.6 kW, nozzle to heating surface distances of 3 cm, 5 cm and 8 cm and cooling oil flow rates of 2 LPM, 3 LPM and 4 LPM are studied on the performance characteristics of direct spray oil cooling system. The lowest maximum surface temperature is obtained for spiral nozzle with 5 cm distance and both full cone nozzles with 8 cm distance. The maximum temperature is maintained within 140 & DEG;C at low heating ca-pacity of 1.3 kW and different combinations of nozzles and cooling oils are tested considering flow rate range of 2 LPM to 4 LPM to maintain the maximum temperature within cut-off limit of 200 & DEG;C at high heating capacity of 2.6 kW. The maximum performance characteristics are obtained at 4 LPM flow rate followed by 3 LPM and 2 LPM flow rates, respectively in decreasing order. The dielectric oil shows supe-rior performance characteristics compared to mineral oil and transmission oil for all nozzles. Furthermore, in each case of cooling oil, the performance characteristics are excellent for full cone-1 nozzle compared to spiral and full cone-2 nozzles. The combination of dielectric oil and full cone-1 nozzle shows superior performance characteristics of direct spray oil cooling system with heat transfer coefficient of 67420.20 W/m2-K, Nusselt number of 2385.64, spray resistance of 0.0132 K/W and spray power consumption of 29.73 W. The data base generated for a direct spray oil cooling system will be implemented for cooling of an electric vehicle driving motor.(c) 2022 Elsevier Ltd. All rights reserved.
引用
收藏
页数：19
相关论文
共 53 条
[1]   Study on Ultra-fast Cooling Behaviors of Water Spray Cooled Stainless Steel Plates [J].
Aamir, Muhammad ;
Qiang, Liao ;
Xun, Zhu ;
Wang, Hong ;
Ullah, Ramzan .
EXPERIMENTAL HEAT TRANSFER, 2016, 29 (03) :299-321
[2]   An investigation of the influence of surface roughness, water quality and nozzle on spray cooling of Aluminum alloy 6082 [J].
Ali, Kabbir ;
Amna, Riffat ;
Rashid, Muhammad Usman ;
Malik, M. Irfan ;
Kim, Kiseong .
THERMAL SCIENCE AND ENGINEERING PROGRESS, 2019, 10 :280-286
[3]  
[Anonymous], 1995, Advances in Heat Transfer, DOI DOI 10.1016/S0065-2717(08)70296-X
[4]   Upward-facing multi-nozzle spray cooling experiments for external cooling of reactor pressure vessels [J].
Bandaru, Satya V. Ravikumar ;
Villanueva, Walter ;
Konovalenko, Alexander ;
Komlev, Andrei ;
Thakre, Sachin ;
Skold, Per ;
Bechta, Sevostian .
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2020, 163
[5]   Analysis on the influences of atomization characteristics on heat transfer characteristics of spray cooling [J].
Bao, Jun ;
Wang, Yu ;
Xu, Xinjie ;
Niu, Xiaoyi ;
Liu, Jinxiang ;
Qiu, Lanlan .
SUSTAINABLE CITIES AND SOCIETY, 2019, 51
[6]   Heat transfer during multiple droplet impingement and spray cooling: Review and prospects for enhanced surfaces [J].
Benther, J. D. ;
Pelaez-Restrepo, J. D. ;
Stanley, C. ;
Rosengarten, G. .
INTERNATIONAL JOURNAL OF HEAT AND MASS TRANSFER, 2021, 178
[7]  
Berenson P.J., 1962, International Journal of Heat and Mass Transfer, V5, P985, DOI DOI 10.1016/0017-9310(62)90079-0
[8]   Three dimensional numerical analysis of heat transfer during spray quenching of 22MnB5 steel with a single nozzle [J].
Bulut, Emre ;
Sevilgen, Gokhan ;
Esiyok, Ferdi ;
Ozturk, Ferruh ;
Abi, Tugce Turan .
HEAT AND MASS TRANSFER, 2021, 57 (06) :961-974
[9]   Numerical investigation on heat transfer of water spray cooling from single-phase to nucleate boiling region [J].
Cai, Chang ;
Liu, Hong ;
Jia, Ming ;
Yin, Hongchao ;
Xie, Rong ;
Yan, Peiliang .
INTERNATIONAL JOURNAL OF THERMAL SCIENCES, 2020, 151 (151)
[10]   NUMERICAL SIMULATION OF SINGLE-NOZZLE LARGE SCALE SPRAY COOLING ON DRUM WALL [J].
Chen, Zuobing ;
Xie, Qiang ;
Chen, Gong ;
Yu, Yongjie ;
Zhao, Zheyu .
THERMAL SCIENCE, 2018, 22 (01) :359-370
123456