The measurement of the adhesion force between ceramic particles and metal matrix in ceramic reinforced-metal matrix composites

被引：40

作者：

Jarzabek, Dariusz M. ^{[1
]}

Chmielewski, Marcin ^{[2
]}

Wojciechowski, Tomasz

机构：

[1] Inst Fundamental Technol Res, PL-00049 Warsaw, Poland

[2] Inst Elect Mat Technol, Warsaw, Poland

来源：

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING | 2015年 / 76卷

关键词：

Nanocomposites; Metal matrix composites; Adhesion; Interface; SHAPE-MEMORY ALLOY; RESIDUAL-STRESSES; STRENGTH; INTERFACE; ION; MICROSTRUCTURE; SIMULATION; TOUGHNESS; MODULUS; DESIGN;

D O I：

10.1016/j.compositesa.2015.05.025

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

This paper presents the method for measurement of the adhesion force and fracture strength of the interface between ceramic particles and metal matrix in ceramic reinforced-metal matrix composites. Three samples with the following Cu to Al2O3 ratio (in vol.%) were prepared: 98.0Cu/2.0Al(2)O(3), 95.0Cu/5.0Al(2)O(3) and 90Cu/10Al(2)O(3). Furthermore, microwires which contain a few ceramic particles were produced by means of electro etching. The microwires with clearly exposed interface were tested with use of the microtensile tester. The microwires usually break exactly at the interface between the metal matrix and ceramic particle. The force and the interface area were carefully measured and then the fracture strength of the interface was determined. The strength of the interface between ceramic particle and metal matrix was equal to 59 +/- 8 MPa and 59 +/- 11 MPa in the case of 2% and 5% Al2O3 to Cu ratio, respectively. On the other hand, it was significantly lower (38 +/- 5 MPa) for the wires made of composite with 10% Al2O3. (C) 2015 Elsevier Ltd. All rights reserved.

引用

页码：124 / 130

页数：7

共 34 条

[1] Effects of manufacturing parameters on residual stresses in SiC/Ti composites by an elastic-viscoplastic micromechanical model [J].

Aghdam, M. M. ;

Morsali, S. R. .

COMPUTATIONAL MATERIALS SCIENCE, 2014, 91 :62-67

[2] Laminate squeeze casting of carbon fiber reinforced aluminum matrix composites [J].

Alhashmy, Hasan Ali ;

Nganbe, Michel .

MATERIALS & DESIGN, 2015, 67 :154-158

[3] Novel thermoplastic polymers with improved release properties for thermal NIL [J].

Atasoy, H. ;

Vogler, M. ;

Haatainen, T. ;

Schleunitz, A. ;

Jarzabek, D. ;

Schift, H. ;

Reuther, F. ;

Gruetzner, G. ;

Rymuza, Z. .

MICROELECTRONIC ENGINEERING, 2011, 88 (08) :1902-1905

[4] Fabrication of carbon fiber reinforced aluminum matrix composites via a titanium-ion containing flux [J].

Baumli, P. ;

Sychev, J. ;

Budai, I. ;

Szabo, J. T. ;

Kaptay, G. .

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING, 2013, 44 :47-50

[5] Comparison of experimental and modelling results of thermal properties in Cu-AlN composite materials [J].

Chmielewski, M. ;

Weglewski, W. .

BULLETIN OF THE POLISH ACADEMY OF SCIENCES-TECHNICAL SCIENCES, 2013, 61 (02) :507-514

[6]

Chmielewski M, 2010, ARCH METALL MATER, V55, P579

[7] An etching based axisymmetric solution for the determination of residual stresses in long fibre reinforced metal matrix composites [J].

Durodola, J. F. ;

Parikh, T. S. ;

Fellows, N. A. ;

Gungor, S. .

JOURNAL OF COMPOSITE MATERIALS, 2014, 48 (19) :2375-2386

[8] Effect of particle orientation anisotropy on the tensile behavior of metal matrix composites: experiments and micro structure-based simulation [J].

Ganesh, VV ;

Chawla, N .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2005, 391 (1-2) :342-353

[9] Measurement of the bending strength of vapor-liquid-solid grown silicon nanowires [J].

Hoffmann, S ;

Utke, I ;

Moser, B ;

Michler, J ;

Christiansen, SH ;

Schmidt, V ;

Senz, S ;

Werner, P ;

Gösele, U ;

Ballif, C .

NANO LETTERS, 2006, 6 (04) :622-625

[10] Elastic modulus and fracture strength evaluation on the nanoscale by scanning force microscope experiments [J].

Jarzabek, D. M. ;

Kaufmann, A. N. ;

Schift, H. ;

Rymuza, Z. ;

Jung, T. A. .

NANOTECHNOLOGY, 2014, 25 (21)

← 1 2 3 4 →