The effect of cryogenic rolling on the formation of ultra-fine grains in 5052 Al alloy

被引：0
|
作者：
Lee, YB [1 ]
Nam, WJ [1 ]
Shin, DH [1 ]
机构：
[1] Kookmin Univ, Sch Adv Mat Engn, Seoul 136702, South Korea
来源：
ULTRAFINE GRAINED MATERIALS III | 2004年
关键词：
cryogenic temperature; ultrafine grain; annealing; Al alloys;
D O I：
暂无
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
The large deformation at cryogenic temperature would be one of the effective methods to produce large bulk UFG materials. The effects of annealing temperature on microstructure and mechanical properties of the sheets received 88% reduction at cryogenic temperature were investigated for the annealing temperature of 150 similar to 300degrees C, in comparison with those at room temperature. Annealing of 5052 Al alloy deformed 88%, at 200degrees C for an hour, results in the considerable increase of tensile elongation without the great loss of strength and the occurrence of equiaxed grains less than 300nm in diameter.
引用
收藏
页码：363 / 368
页数：6
相关论文
共 50 条
  • [31] Effect of nitrogen on structure and properties of ultra-fine austenitic stainless steel
    Liu Jing
    Li Guang-qiang
    Peng Bing
    Mang Xin
    JOURNAL OF IRON AND STEEL RESEARCH INTERNATIONAL, 2007, 14 : 310 - 315
  • [32] The achievement of high strength in an Al 6061 alloy by the application of cryogenic and warm rolling
    U. G. Kang
    H. J. Lee
    W. J. Nam
    Journal of Materials Science, 2012, 47 : 7883 - 7887
  • [33] Effect of annealing temperature on microstructures and mechanical properties of a 5083 Al alloy deformed at cryogenic temperature
    Lee, YB
    Shin, DH
    Park, KT
    Nam, WJ
    SCRIPTA MATERIALIA, 2004, 51 (04) : 355 - 359
  • [34] Effect of Heat Treatment on Microstructure and Mechanical Properties of Ultra-fine Grained TI-55511 Near β Titanium Alloy
    Li Chao
    Zhang Xiaoyong
    Li Zhiyou
    Zhou Kechao
    RARE METAL MATERIALS AND ENGINEERING, 2015, 44 (02) : 327 - 332
  • [35] New Groove Design and Three-dimensional Numerical Simulation of Ultra-fine Grain of Bar Rolling
    Cao, Lei
    Li, Xuetong
    Liu, Shujian
    Wang, Minting
    FRONTIERS OF MATERIALS, CHEMICAL AND METALLURGICAL TECHNOLOGIES, PTS 1 AND 2, 2012, 581-582 : 879 - 882
  • [36] Microstructure stability and mechanical properties of ultrafine grained 5052 Al alloy fabricated by differential speed rolling
    Ko, Young Gun
    Hamad, Kotiba
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2018, 733 : 24 - 27
  • [37] Superplasticity and its application of ultra-fine grained Ti-6Al-4V alloy obtained through protium treatment
    Nakahigashi, J
    Yoshimura, H
    MATERIALS TRANSACTIONS, 2002, 43 (11) : 2768 - 2772
  • [38] Fatigue Behavior of Ultrafine-Grained 5052 Al Alloy Processed Through Different Rolling Methods
    K. K. Yogesha
    Amit Joshi
    R. Jayaganthan
    Journal of Materials Engineering and Performance, 2017, 26 : 2826 - 2836
  • [39] Fatigue Behavior of Ultrafine-Grained 5052 Al Alloy Processed Through Different Rolling Methods
    Yogesha, K. K.
    Joshi, Amit
    Jayaganthan, R.
    JOURNAL OF MATERIALS ENGINEERING AND PERFORMANCE, 2017, 26 (06) : 2826 - 2836
  • [40] Ultrastrong and ductile austenitic lightweight steel via ultra-fine grains and heterogeneous B2 precipitates
    An, Y. F.
    Chen, X. P.
    Ren, P.
    Cao, W. Q.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2022, 860
12345