Setup of an Experimental Facility for the Investigation of Wet Compression on a Multistage Compressor

被引:26
作者
Bettocchi, R. [1 ]
Morini, M. [1 ]
Pinelli, M. [1 ]
Spina, P. R. [1 ]
Venturini, M. [1 ]
Torsello, G. [2 ]
机构
[1] Univ Ferrara, Dipartimento Ingn, I-44122 Ferrara, Italy
[2] RSE SpA, Dipartimento SSG, I-20134 Milan, Italy
来源
JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME | 2011年 / 133卷 / 10期
关键词
TURBINE FOGGING TECHNOLOGY; INLET;
D O I
10.1115/1.4002947
中图分类号
TH [机械、仪表工业];
学科分类号
0802 ;
摘要
At present, inlet fogging and wet compression are two of the most widely used approaches to enhance gas turbine performance, especially during hot seasons. However, potentially negative effects of these practices on long-term operational integrity of gas turbines should be evaluated carefully; in particular, wet compression may lead to the erosion of first compressor stages due to the impact of water droplets within the flow at compressor intake. This issue is still controversial in technical literature since only limited historical field operating data and information are available. Therefore, a test facility was specifically set up in the laboratories of the University of Ferrara, to evaluate the effects of wet compression on a small-size compressor. This paper presents the experimental facility developed for wet compression investigation and some preliminary results. [DOI: 10.1115/1.4002947]
引用
收藏
页数:8
相关论文
共 28 条
  • [1] [Anonymous], GT200959365 ASME
  • [2] Application of a computational code to simulate interstage injection effects on GE frame 7EA gas turbine
    Bagnoli, M.
    Bianchi, M.
    Melino, F.
    Peretto, A.
    Spina, P. R.
    Ingistov, S.
    Bhargava, R. K.
    [J]. JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME, 2008, 130 (01):
  • [3] A multistage compressor test facility: Uncertainty analysis and preliminary test results
    Bettocchi, R
    Pinelli, M
    Spina, PR
    [J]. JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME, 2005, 127 (01): : 170 - 177
  • [4] Gas turbine fogging technology: A state-of-the-art review - Part III: Practical considerations and operational experience
    Bhargava, R. K.
    Meher-Homji, C. B.
    Chaker, M. A.
    Bianchi, M.
    Melino, F.
    Peretto, A.
    Ingistov, S.
    [J]. JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME, 2007, 129 (02): : 461 - 472
  • [5] Gas turbine fogging technology: A state-of-the-art review - Part I: Inlet evaporative fogging - Analytical and experimental aspects
    Bhargava, R. K.
    Meher-Homji, C. B.
    Chaker, M. A.
    Bianchi, M.
    Melino, F.
    Peretto, A.
    Ingistov, S.
    [J]. JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME, 2007, 129 (02): : 443 - 453
  • [6] Gas turbine fogging technology: A state-of-the-art review - Part II: Overspray fogging - Analytical and experimental aspects
    Bhargava, R. K.
    Meher-Homji, C. B.
    Chaker, M. A.
    Bianchi, M.
    Melino, F.
    Peretto, A.
    Ingistov, S.
    [J]. JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER-TRANSACTIONS OF THE ASME, 2007, 129 (02): : 454 - 460
  • [7] Bhargava R.K., 2009, ASME Paper, No.GT2009-59920
  • [8] Bhargava R. K., 2008, GT200850761 ASME
  • [9] Bianchi M., 2007, ECOS 20 INT C EFF CO
  • [10] Brun K., 2008, GT200850207 ASME