Characterisation of fracture behaviour of starch gels using conventional fracture mechanics and wire cutting tests

被引：0

作者：

Gamonpilas, C. ^{[1
]}

Charalambides, M. N. ^{[1
]}

Williams, J. G. ^{[1
]}

Dooling, P. J. ^{[2
]}

Gibbon, S. R. ^{[2
]}

机构：

[1] Univ London Imperial Coll Sci Technol & Med, Dept Mech Engn, London SW7 2AZ, England

[2] Wilton Ctr, ICI Appl Res, Redcar TS10 4RF, England

来源：

XVTH INTERNATIONAL CONGRESS ON RHEOLOGY - THE SOCIETY OF RHEOLOGY 80TH ANNUAL MEETING, PTS 1 AND 2 | 2008年 / 1027卷

关键词：

starch gels; fracture toughness; wire cutting; finite element analysis;

D O I：

暂无

中图分类号：

O59 [应用物理学];

学科分类号：

摘要：

The fracture behaviour of starch gels is investigated through experimental tests and finite element simulations. Both conventional fracture and wire cutting experiments were performed. The results from these two tests were consistent with the fracture toughness increasing with loading rate. In the FE analysis, a non-linear elastic constitutive relationship was used to model the starch gels and frictionless condition was assumed between the wire-starch gel contact interface. A failure criterion based on critical fracture strain was assumed. Predictions of the steady-state cutting force at various wire diameters were found to be in good agreement with the wire cutting data.

引用

页码：1232 / +

页数：2

共 50 条

[31] Mixed-mode fracture behavior of AM60 magnesium alloy using two parameter fracture mechanics [J].

Oskui, Abuzar Es'haghi ;

Soltani, Nasser ;

Rajabi, Mohammad ;

Schmauder, Siegfried .

ENGINEERING FRACTURE MECHANICS, 2019, 218

[32] COMPATIBILITY OF FRACTURE MECHANICS PARAMETERS AND FATIGUE CRACK GROWTH PARAMETERS IN WELDED JOINT BEHAVIOUR EVALUATION [J].

Camagic, Ivica ;

Vasic, Nemanja ;

Vasic, Zlatibor ;

Burzic, Zijah ;

Sedmak, Aleksandar .

TEHNICKI VJESNIK-TECHNICAL GAZETTE, 2013, 20 (02) :205-211

[33] Fracture loads of ISRM-suggested notched semi-circular bend rock specimens using finite fracture mechanics [J].

Pan, Junyang ;

Zhang, Zhiqian ;

Liu, Wei ;

Pi, Mengru ;

Liu, Bowen .

THEORETICAL AND APPLIED FRACTURE MECHANICS, 2025, 139

[34] Assessment of Fracture Toughness Using Small Punch Tests of Prenotched Specimens [J].

Zheng, Yangyan ;

Chen, Xiao ;

Yang, Zheng ;

Ling, Xiang .

JOURNAL OF PRESSURE VESSEL TECHNOLOGY-TRANSACTIONS OF THE ASME, 2017, 139 (05)

[35] Characterising fibre compression fracture toughness of composites using bearing tests [J].

Chishti, Maajid ;

Wang, Chun H. ;

Thomson, Rodney S. ;

Orifici, Adrian C. .

COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING, 2012, 43 (10) :1775-1782

[36] Application of Nonlinear Fracture Mechanics Parameter to Predicting Wire-Liftoff Lifetime of Power Module at Elevated Temperatures [J].

Shishido, Nobuyuki ;

Hayama, Yutaka ;

Morooka, Wataru ;

Hagihara, Seiya ;

Miyazaki, Noriyuld .

IEEE JOURNAL OF EMERGING AND SELECTED TOPICS IN POWER ELECTRONICS, 2019, 7 (03) :1604-1614

[37] Investigation on the fracture behaviour of wire arc additive manufactured rotor steel weldments after heat treatment [J].

Mohiuddin, Mohd Durvesh ;

Mohideen, S. Rasool .

THEORETICAL AND APPLIED FRACTURE MECHANICS, 2022, 119

[38] Fracture behaviour of functionally graded bi-material interface produced by wire arc additive manufacturing [J].

Argumedo, J. L. Galan ;

Riemslag, A. C. ;

Hermans, M. J. M. ;

Popovich, V. A. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2025, 928

[39] Fracture toughness, chip types and the mechanics of cutting wood. A review COST Action E35 2004-2008: Wood machining - micromechanics and fracture [J].

Wyeth, David J. ;

Goli, Giacomo ;

Atkins, Anthony G. .

HOLZFORSCHUNG, 2009, 63 (02) :168-180

[40] Prediction of debonding strength of tensile hybrid bonded joints using fracture mechanics [J].

Zhou, Yinzhi ;

Jiang, Kebin ;

Gou, Mingkang ;

Li, Ning ;

Zhu, Pengcheng ;

Wang, Dan ;

Qu, Zhanxin .

MATERIALS & DESIGN, 2014, 61 :87-100

← 1 2 3 4 5 →