ABRASIVE WEAR OF PLASTIC MOLDING STEELS DURING INJECTION MOLDING

被引：0
作者：
Olah, Laszlo [1 ]
Friesenbichler, Walter [1 ]
Borbas, Lajos [1 ]
机构：
[1] Polymer Competence Ctr Leoben GmbH, A-8700 Leoben, Austria
来源：
25TH DANUBIA-ADRIA SYMPOSIUM ON ADVANCES IN EXPERIMENTAL MECHANICS | 2008年
关键词：
D O I：
暂无
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
引用
收藏
页码：195 / 196
页数：2
相关论文
共 50 条
[41]   Gate location optimization scheme for plastic injection molding [J].
Zhai, Ming ;
Lam, Yeecheong ;
Au, Chikit .
E-Polymers, 2009,
[42]   Analysis of thermal residual stress in plastic injection molding [J].
Chen, X ;
Lam, YC ;
Li, DQ .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2000, 101 (1-3) :275-280
[43]   Towards sustainable injection molding of ABS plastic products [J].
Tranter, Jack B. ;
Refalo, Paul ;
Rochman, Arif .
JOURNAL OF MANUFACTURING PROCESSES, 2017, 29 :399-406
[44]   Process parameter optimization of plastic injection molding: a review [J].
Kashyap, Satadru ;
Datta, Dilip .
INTERNATIONAL JOURNAL OF PLASTICS TECHNOLOGY, 2015, 19 (01) :1-18
[45]   Three-dimensional simulation of plastic injection molding [J].
Talwar, K ;
Costa, F ;
Rajupalem, V ;
Antanovski, L ;
Friedl, C .
CONFERENCE PROCEEDINGS AT ANTEC '98: PLASTICS ON MY MIND, VOLS I-3: VOL I; PROCESSING, VOL II; SPECIAL AREAS, VOL III; MATERIALS, 1998, 44 :562-566
[46]   Plastic scintillator produced by the injection-molding technique [J].
Yoshimura, Y ;
Inagaki, T ;
Morimoto, T ;
Sugai, I ;
Kuriki, M ;
Shirai, R ;
Goto, M ;
Yamashina, T .
NUCLEAR INSTRUMENTS & METHODS IN PHYSICS RESEARCH SECTION A-ACCELERATORS SPECTROMETERS DETECTORS AND ASSOCIATED EQUIPMENT, 1998, 406 (03) :435-441
[47]   Injection molding higher performance reinforced plastic composites [J].
Rosato, DV .
JOURNAL OF VINYL & ADDITIVE TECHNOLOGY, 1996, 2 (03) :216-220
[48]   On the pvT and thermal shrinkage for the injection molding of a plastic lens [J].
Chang, RY ;
Hsieh, YC ;
Hsu, CH .
CONFERENCE PROCEEDINGS AT ANTEC '98: PLASTICS ON MY MIND, VOLS I-3: VOL I; PROCESSING, VOL II; SPECIAL AREAS, VOL III; MATERIALS, 1998, 44 :574-578
[49]   An explanatory study on defects in plastic molding parts caused by machine parameters in injection molding process [J].
Mourya A. ;
Nanda A. ;
Parashar K. ;
Sushant ;
Kumar R. .
Materials Today: Proceedings, 2023, 78 :656-661
[50]   On the pvT and thermal shrinkage for the injection molding of a plastic lens [J].
Chang, RY ;
Hsieh, YC ;
Hsu, CH .
JOURNAL OF REINFORCED PLASTICS AND COMPOSITES, 1999, 18 (03) :261-270
12345