ABRASIVE WEAR OF PLASTIC MOLDING STEELS DURING INJECTION MOLDING

被引：0
作者：
Olah, Laszlo [1 ]
Friesenbichler, Walter [1 ]
Borbas, Lajos [1 ]
机构：
[1] Polymer Competence Ctr Leoben GmbH, A-8700 Leoben, Austria
来源：
25TH DANUBIA-ADRIA SYMPOSIUM ON ADVANCES IN EXPERIMENTAL MECHANICS | 2008年
关键词：
D O I：
暂无
中图分类号：
TH [机械、仪表工业];
学科分类号：
0802 ;
摘要：
引用
收藏
页码：195 / 196
页数：2
相关论文
共 50 条
[31]   Comparison of Molding Characteristics for Multi-cavity Molding in Conventional Injection Molding and Injection Compression Molding [J].
Lee, Dan Bi ;
Nam, Yun Hyo ;
Lyu, Min-Young .
POLYMER-KOREA, 2014, 38 (02) :144-149
[32]   Fabrication of high speed steels by metal injection molding [J].
Miura, Hideshi ;
Gondou, Hiroshi ;
Kouno, Tomio ;
Honda, Tadatoshi .
Funtai Oyobi Fummatsu Yakin/Journal of the Japan Society of Powder and Powder Metallurgy, 1993, 40 (04) :393-396
[33]   THREE DIMENSIONAL NUMERICAL SIMULATION OF POLYMER CRYSTALLIZATION DURING PLASTIC INJECTION MOLDING [J].
Yan Bo ;
Li Yang ;
Kong Xiao ;
Zhao Peng ;
Li Dequn .
ACTA POLYMERICA SINICA, 2011, (02) :173-179
[34]   Compact injection molding and special injection molding techniques [J].
Brinkmann, S .
KUNSTSTOFFE-PLAST EUROPE, 1997, 87 (10) :1410-&
[35]   Influence of the injection molding process on the tooth deflection of plastic gears during operation [J].
Herzog C. ;
Drummer D. .
VDI Berichte, 2023, 2023 (2422) :1435-1448
[36]   Damage of the cell wall during extrusion and injection molding of wood plastic composites [J].
Gacitua, William ;
Bahr, David ;
Wolcott, Michael .
COMPOSITES PART A-APPLIED SCIENCE AND MANUFACTURING, 2010, 41 (10) :1454-1460
[37]   Flowing deviation behavior of plastic melt during micro injection molding process [J].
Guo, Youdan ;
Cheng, Xiaonong .
Huagong Xuebao/CIESC Journal, 2015, 66 (06) :2329-2335
[38]   INJECTION MOLDING OF THERMOSETTING PLASTICS THERMOSET INJECTION MOLDING [J].
GARDNER, HM ;
BURGESSH.MG .
SPE JOURNAL, 1966, 22 (02) :29-&
[39]   Energy use during injection molding [J].
Prenatt, CM .
ANTEC '96: PLASTICS - RACING INTO THE FUTURE, VOLS I-III: VOL I: PROCESSING; VOL II: MATERIALS; VOL III: SPACIAL AREAS, 1996, 42 :3489-3491
[40]   Instrumental analysis during injection molding [J].
Campbell, GA ;
Savoca, J ;
Campbell, S ;
Bullwinkel, M ;
Nagarajan, G ;
Wang, CC .
ANTEC '96: PLASTICS - RACING INTO THE FUTURE, VOLS I-III: VOL I: PROCESSING; VOL II: MATERIALS; VOL III: SPACIAL AREAS, 1996, 42 :3577-3586
12345