Study of the welding conditions during similar and dissimilar aluminium and copper welding based on torque sensitivity analysis

被引:28
|
作者
Galvao, I. [1 ]
Leitao, C. [1 ]
Loureiro, A. [1 ]
Rodrigues, D. M. [1 ]
机构
[1] Univ Coimbra, Dept Mech Engn, CEMUC, P-3030788 Coimbra, Portugal
来源
MATERIALS & DESIGN | 2012年 / 42卷
关键词
FRICTION STIR WELDS; BRITTLE STRUCTURES; PARAMETERS; GEOMETRY; ALLOYS; SHEETS; POWER;
D O I
10.1016/j.matdes.2012.05.058
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
The aim of present study was to analyse and compare the influence of the welding conditions on torque evolution, during similar and dissimilar friction stir butt welding of 5083-H111 aluminium alloy and copper-DHP. The torque registered during welding, using different welding parameters and base materials combinations, and its relation with the morphological and structural properties of the welds were analysed. Independently of the materials to be welded and the relative plates positioning, in dissimilar friction stir welding, the sensitivity of the average torque to the process parameters was observed to be the same. It was also observed that the average torque is strongly conditioned by the materials to be welded, since, for all welding parameters, the lowest average torque values were always registered during dissimilar welding. Material flow and intermetallic-formation were found to determine this behaviour. Important differences in instantaneous torque evolution, during welding, were also observed depending on base materials combinations. (C) 2012 Elsevier Ltd. All rights reserved.
引用
收藏
页码:259 / 264
页数:6
相关论文
共 50 条
  • [31] Effect of Welding Parameters on Lap Shear Force of Similar and Dissimilar Friction Stir Spot Welded Aluminium Alloys
    Mohan, Ahmed Esmael
    Sajuri, Zainuddin
    Baghdadi, Amir Hossein
    Jamadon, Nashrah Hani
    JURNAL KEJURUTERAAN, 2024, 36 (03): : 1187 - 1198
  • [32] A Comparison of the Inertia Friction Welding Behavior of Similar and Dissimilar Ni-Based Superalloys
    Senkov, O. N.
    Mahaffey, D. W.
    Semiatin, S. L.
    METALLURGICAL AND MATERIALS TRANSACTIONS A-PHYSICAL METALLURGY AND MATERIALS SCIENCE, 2018, 49A (11): : 5428 - 5444
  • [33] A Comparison of the Inertia Friction Welding Behavior of Similar and Dissimilar Ni-Based Superalloys
    O. N. Senkov
    D. W. Mahaffey
    S. L. Semiatin
    Metallurgical and Materials Transactions A, 2018, 49 : 5428 - 5444
  • [34] Experimental and numerical simulation study of magnesium/aluminium dissimilar metal swing laser welding
    Cui, Mengfei
    Zheng, Zhentai
    Du, Peng
    Cheng, Zhanchang
    MATERIALS TODAY COMMUNICATIONS, 2024, 39
  • [35] A review study in ultrasonic-welding of similar and dissimilar thermoplastic polymers and its composites
    Unnikrishnan, T. G.
    Kavan, Panneerselvam
    MATERIALS TODAY-PROCEEDINGS, 2022, 56 : 3294 - 3300
  • [36] Effect of hybrid reinforcement at stirred zone of dissimilar aluminium alloys during friction stir welding
    Kumar, R. Ashok
    Raghav, G. R.
    Nagarajan, K. J.
    Rengarajan, Sathish
    Suganthi, P.
    Vignesh, V.
    METALLURGICAL RESEARCH & TECHNOLOGY, 2019, 116 (06)
  • [37] Investigation of the microstructural, mechanical, and thermal evolution of dissimilar aluminium alloys during friction stir welding
    Kasirajan, T.
    Ravindran, R.
    Ramkumar, T.
    Selvakumar, M.
    TRANSACTIONS OF THE CANADIAN SOCIETY FOR MECHANICAL ENGINEERING, 2020, 44 (01) : 38 - 48
  • [38] Process study for friction stir lap welding of copper/steel dissimilar metals
    Zhou L.
    Jiang Z.
    Lei S.
    Yu M.
    Zhao H.
    Hanjie Xuebao/Transactions of the China Welding Institution, 2019, 40 (04): : 22 - 27
  • [39] A comprehensive review of microstructure evolution during friction stir welding of aluminium to copper
    Medhi T.
    Roy B.S.
    Saha S.C.
    Medhi, Tanmoy (tanmoymedhi@gmail.com), 2018, Inderscience Publishers, 29, route de Pre-Bois, Case Postale 856, CH-1215 Geneva 15, CH-1215, Switzerland (57) : 1 - 19
  • [40] A comprehensive review of microstructure evolution during friction stir welding of aluminium to copper
    Medhi, Tanmoy
    Roy, Barnik Saha
    Saha, Subhash Chandra
    INTERNATIONAL JOURNAL OF MATERIALS & PRODUCT TECHNOLOGY, 2018, 57 (1-3): : 1 - 19