THE EFFECTS OF CUTTING TOOL COATING AND MACHINING PARAMETERS IN DRILLING OF STEEL AISI H13 AND AISI D2

被引:0
作者
Tekaut, Ismail [1 ]
Demir, Halil [2 ]
机构
[1] Gazi Univ, Tekn Bilimler MYO, Ankara, Turkey
[2] Karabuk Univ, Teknol Fak, Imalat Muhendisligi, Karabuk, Turkey
来源
JOURNAL OF THE FACULTY OF ENGINEERING AND ARCHITECTURE OF GAZI UNIVERSITY | 2015年 / 30卷 / 02期
关键词
Drilling; AISI H13; AISI D2; tool coating; temperature measurement; TEMPERATURE; MICROSTRUCTURE; BEHAVIOR; STRESS;
D O I
暂无
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
In drilling, temperature is an important factor for the tool and the machining performance. For this reason, analysis of the temperature in the cutting zone is essential for predicting the machining performance. In this study, commonly used AISI H13 and AISI D2 steels were drilled using uncoated and (AlCrN monolayer) coated carbide drills of 14 mm diameter on a vertical machining centre. The cutting zone temperatures were determined using the thermocouples inserted into the coolant holes of the drills. The tests were carried out at four different cutting speeds (60, 75, 90 and 108 m/min) and three different feed rates (0.15, 0.20 and 0.25 mm/rev). The experimental results showed that increasing feed rate and cutting speed led to decrease in the temperature. The lower heat conduction of the coated drills resulted in the higher temperature. In all the tests, drilling of AISI H13 caused higher temperature than that of AISI D2. It is considered that this was caused by the structural and chemical differences of the materials.
引用
收藏
页码:289 / 296
页数:8
相关论文
共 26 条
[1]  
Aydin M., 2010, ULUSAL TASARIM IMALA, P85
[2]   Finite element and experimental investigation of temperature changes on a twist drill in sequential dry drilling [J].
Bagci, E ;
Ozcelik, B .
INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2006, 28 (7-8) :680-687
[3]   Microstructure and corrosion behaviour of pulsed plasma-nitrided AISI H13 tool steel [J].
Basso, Rodrigo L. O. ;
Pastore, Heloise O. ;
Schmidt, Vanessa ;
Baumvol, Israel J. R. ;
Abarcad, Silvia A. C. ;
de Souza, Fernando S. ;
Spinelli, Almir ;
Figueroa, Carlos A. ;
Giacomelli, Cristiano .
CORROSION SCIENCE, 2010, 52 (09) :3133-3139
[4]   Contribution to dynamic characteristics of the cutting temperature in the drilling process considering one dimension heat flow [J].
Brandao, Lincoln Cardoso ;
Coelho, Reginaldo Teixeira ;
Lauro, Carlos Henrique .
APPLIED THERMAL ENGINEERING, 2011, 31 (17-18) :3806-3813
[5]  
Cakir M.C., 1999, MODERN TALASLI IMAL
[6]  
da Silva MB, 1999, J MATER PROCESS TECH, V88, P195
[7]   Machinability evaluation in hard turning of cold work tool steel (D2) with ceramic tools using statistical techniques [J].
Davim, J. Paulo ;
Figueira, Luis .
MATERIALS & DESIGN, 2007, 28 (04) :1186-1191
[8]   Estimation of heat flux and temperature field during drilling process using dynamic observers based on Green's function [J].
de Sousa, Priscila F. B. ;
Borges, Valerio L. ;
Pereira, Igor C. ;
da Silva, Marcio B. ;
Guimaraes, Gilmar .
APPLIED THERMAL ENGINEERING, 2012, 48 :144-154
[9]   Boriding kinetics of H13 steel [J].
Genel, K .
VACUUM, 2006, 80 (05) :451-457
[10]  
Ghani J. A., 2004, J MATER PROCESS TECH, V153-154, P1062