Effects of the heterogeneity in the electron beam welded joint on fatigue crack growth in Ti-6Al-4V alloy

被引：39
作者：
Li, Xingzhi [1 ]
Hu, Shubing [1 ]
Xiao, Jianzhong [1 ]
Ji, Longbo [1 ]
机构：
[1] Huazhong Univ Sci & Technol, State Key Lab Mat Proc & Die Mould Technol, Wuhan 430074, Peoples R China
来源：
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING | 2011年 / 529卷
关键词：
Titanium alloys; Fatigue; Heterogeneity; Electron beam welding; TITANIUM-ALLOY; RESIDUAL-STRESS; MICROSTRUCTURE; BEHAVIOR; PROPAGATION; FRACTURE; PLATE;
D O I：
10.1016/j.msea.2011.09.014
中图分类号：
TB3 [工程材料学];
学科分类号：
0805 ; 080502 ;
摘要：
The heterogeneity of electron beam (EB)-welded joints in thick Ti-6Al-4V alloy plates is defined and described. The microstructure, hardness, and fatigue crack growth rate (FCGR) in the fuse zone (FZ) and the heat-affected zone (HAZ) of thick Ti-6Al-4V alloy EB-welded joint are studied using a new testing and interception method. The fatigue fractographs, crack growth paths and the microscopic deformation are observed through scanning and transmission electron microscopy. The effect mechanism of heterogeneity in the electron beam weld joint to FCGRs is discussed. The results reveal that FCGR is higher in the HAZ than in the FZ, mainly because of the effect of heterogeneity! of the welded joint. Heterogeneity II increases from the top to the root of the welding seam while the size of the alpha' phase decreases. Consequently, FCGR is higher at the root of the welding seam. Heterogeneity in the joint is found to greatly influence the FCGR. Crown Copyright (C) 2011 Published by Elsevier B.V. All rights reserved.
引用
收藏
页码：170 / 176
页数：7
相关论文
共 50 条
  • [31] The effects of surface finish on the fatigue performance of electron beam melted Ti-6Al-4V
    Ednie, L.
    Lancaster, R. J.
    Antonysamy, A. A.
    Zelenka, F.
    Scarpellini, A.
    Parimi, L.
    Maddalena, R.
    Barnard, N. C.
    Efthymiadis, P.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2022, 857
  • [32] Tensile and fatigue properties of electron beam welded dissimilar joints between Ti-6Al-4V and BT9 titanium alloys
    Wang, S. Q.
    Liu, J. H.
    Chen, D. L.
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2013, 584 : 47 - 56
  • [33] Study on Biomedical Porous Ti-6Al-4V Alloy Fabricated by Electron Beam Selective Melting
    Tang Huiping
    Yang Guangyu
    Liu Haiyan
    Liu Nan
    Jing Peng
    Li Zengfeng
    Huang Yuanping
    RARE METAL MATERIALS AND ENGINEERING, 2014, 43 : 127 - 131
  • [34] Fatigue Crack Growth Rate of Ti-6Al-4V Considering the Effects of Fracture Toughness and Crack Closure
    Zhang Junhong
    Yang Shuo
    Lin Jiewei
    CHINESE JOURNAL OF MECHANICAL ENGINEERING, 2015, 28 (02) : 409 - 415
  • [35] Effect of HIP Treatment on Fatigue Notch Sensitivity of Ti-6Al-4V Alloy Fabricated by Electron Beam Melting
    Sun, Tao
    Liu, Yan
    Li, Shu-Jun
    Li, Jian-Ping
    ACTA METALLURGICA SINICA-ENGLISH LETTERS, 2019, 32 (07) : 869 - 875
  • [36] Fracture assessment for electron beam welded damage tolerant Ti-6Al-4V alloy by the FITNET procedure
    Wei Lu
    Yaowu Shi
    Xiaoyan Li
    Yongping Lei
    Chinese Journal of Mechanical Engineering, 2013, 26 : 1013 - 1021
  • [37] Internal fatigue crack propagation in a Ti-6Al-4V alloy: An in situ study
    Junet, Arnaud
    Messager, Alexandre
    Weck, Arnaud
    Nadot, Yves
    Boulnat, Xavier
    Buffiere, Jean-Yves
    INTERNATIONAL JOURNAL OF FATIGUE, 2023, 168
  • [38] Fracture Assessment for Electron Beam Welded Damage Tolerant Ti-6Al-4V Alloy by the FITNET Procedure
    Lu Wei
    Shi Yaowu
    Li Xiaoyan
    Lei Yongping
    CHINESE JOURNAL OF MECHANICAL ENGINEERING, 2013, 26 (05) : 1013 - 1021
  • [39] Simulation of fatigue small crack growth in additive manufactured Ti-6Al-4V material
    Gupta, A.
    Sun, W.
    Bennett, C. J.
    CONTINUUM MECHANICS AND THERMODYNAMICS, 2020, 32 (06) : 1745 - 1761
  • [40] Fracture Assessment for Electron Beam Welded Damage Tolerant Ti-6Al-4V Alloy by the FITNET Procedure
    LU Wei
    SHI Yaowu
    LI Xiaoyan
    LEI Yongping
    Chinese Journal of Mechanical Engineering, 2013, (05) : 1013 - 1021
12345