Experimental study on characteristics of laser metal deposited Al-Si-Sn-Cu/Ti-6Al-4V composite coatings

被引：10
|
作者：
Obiegbu, M. C. [1 ]
Fatoba, O. S. [1 ]
Akinlabi, E. T. [1 ,3 ]
Akinlabi, S. A. [2 ]
机构：
[1] Univ Johannesburg, Dept Mech Engn Sci, Johannesburg, South Africa
[2] Univ Johannesburg, Dept Mech & Ind Engn Technol, Johannesburg, South Africa
[3] Covenant Univ, Dept Mech Engn, Ota, Ogun State, Nigeria
来源：
MATERIALS RESEARCH EXPRESS | 2019年 / 6卷 / 04期
基金：
新加坡国家研究基金会;
关键词：
Ti-6Al-4V alloy; hardness; coefficient of friction; microstructure; Al-Si-Sn-Cu coating; laser metal deposition; characterization; AL-SN COATINGS; MECHANICAL-PROPERTIES; CORROSION BEHAVIOR; SURFACE-ANALYSES; HARDNESS VALUES; TITANIUM-ALLOYS; TI COATINGS; MICROSTRUCTURE; POROSITY; SPEED;
D O I：
10.1088/2053-1591/aafe4d
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
The development of laser based advanced coatings are continually implemented in order to meet the desired demands and performances of materials in industries. Many engineering materials used in industrial conditions are subjected to corrosion, wear and fatigue attack leading to rapid degradation of the material. This research is aimed at fabricating Al-Si-Sn-Cu quaternary coatings on Ti-6Al-4V alloy. A 3-kW continuous wave ytterbium laser system (YLS) attached to a KUKA robot which controls the movement of the cladding process was used for the laser cladding process. The appropriate selection of laser processing parameter produced desirable result and properties. Enhanced surface hardness and tribological properties were achieved as a result of well optimized laser process parameters and appropriate selection of reinforced powders. The results of the microhardness revealed an improvement as the hardness measured for the cladded Al-Si-Sn-Cu layer was 602 HV0.1. While the micro-hardness of the Ti-6Al-4V substrate was 302 HV0.1. Also, the COF of Al- Si-Sn-Cu quaternary coatings are lower than that of the Ti-6Al-4V substrate, which was attributed to strengthening effect and higher load bearing aptitude of Ti3Al, CuTi2, AlSi3Ti2, SiTi, AlTi0.6V0.4, and Al0.25Sn0.75V3 hard phases present in the coatings. The protective intermetallic phases result to a reduction in coefficient of friction and therefore demonstrated superior wear resistance performance.
引用
收藏
页数：11
相关论文
共 50 条
  • [1] Experimental Investigation, Characterization, and Microstructural Enhancement of Laser Cladded Al-Si-Sn-Cu/Ti-6Al-4V Composite Coatings
    Fatoba, Olawale Samuel
    Jen, Tien Chien
    PROCEEDINGS OF ASME 2023 INTERNATIONAL MECHANICAL ENGINEERING CONGRESS AND EXPOSITION, IMECE2023, VOL 4, 2023,
  • [2] The Effects of Silicon and Copper on the Microstructure and Wear Resistance Performance of Al-Si-Sn-Cu/Ti-6Al-4V Composite Coatings
    Obiegbu, Mary-Jane C.
    Akinlabi, Esther T.
    Fatoba, Olawale S.
    Akinlabi, Stephen A.
    2019 IEEE 10TH INTERNATIONAL CONFERENCE ON MECHANICAL AND INTELLIGENT MANUFACTURING TECHNOLOGIES (ICMIMT 2019), 2019, : 20 - 25
  • [3] Characterization, Performance and Microstructural Enhancement of Additive Manufactured Al-Si-Sn-Cu/Ti-6Al-4V Composite Coatings
    Fatoba, Olawale Samuel
    Jen, Tien-Chien
    Akinlabi, Esther Titilayo
    2022 IEEE 13TH INTERNATIONAL CONFERENCE ON MECHANICAL AND INTELLIGENT MANUFACTURING TECHNOLOGIES (ICMIMT 2022), 2022, : 30 - 34
  • [4] Numerical Investigation of Laser Deposited Al-Based Coatings on Ti-6Al-4V Alloy
    Fatoba, Olawale S.
    Akinlabi, Stephen A.
    Akinlabi, Esther T.
    PROCEEDINGS OF 2018 IEEE 9TH INTERNATIONAL CONFERENCE ON MECHANICAL AND INTELLIGENT MANUFACTURING TECHNOLOGIES (ICMIMT 2018), 2018, : 85 - 90
  • [5] Data related to optimized process parameters influence on hardness, microstructural evolution and wear resistance performance of Al-Si-Sn-Cu/Ti-6Al-4V composite coatings
    Fatoba, O. S.
    Akinlabi, E. T.
    Akinlabi, S. A.
    Obiegbu, M. C.
    DATA IN BRIEF, 2019, 23
  • [6] Evaluation of microstructure, microhardness, and electrochemical properties of laser-deposited Ti-Co coatings on Ti-6Al-4V Alloy
    Fatoba, O. S.
    Adesina, O. S.
    Popoola, A. P. I.
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2018, 97 (5-8): : 2341 - 2350
  • [7] Effect of scanning speed and powder flow rate on the evolving properties of laser metal deposited Ti-6Al-4V/Cu composites
    Erinosho, Mutiu F.
    Akinlabi, Esther T.
    Pityana, Sisa
    INTERNATIONAL JOURNAL OF SURFACE SCIENCE AND ENGINEERING, 2016, 10 (03) : 207 - 223
  • [8] Dissimilar Laser Welding of Ti-6Al-4V to Ti-6Al-6V-2Sn
    Chiu, C. Y.
    Lu, M. Y.
    Tsay, L. W.
    MANUFACTURING SCIENCE AND TECHNOLOGY, PTS 1-3, 2011, 295-297 : 2353 - 2357
  • [9] Numerical Modelling and Influence of Cu Addition on the Microstructure and Mechanical Properties of Additive Manufactured Ti-Al-Cu/Ti-6Al-4V Composite
    Akinlabi, E. T.
    Fatoba, O. S.
    Akinlabi, S. A.
    MATERIALS PROCESSING FUNDAMENTALS 2019, 2019, : 143 - 152
  • [10] Material characterization and corrosion behavior of hybrid coating Ti-Al-Si-Cu/Ti-6Al-4V compositeMaterialcharakterisierung und Korrosionsverhalten von hybridbeschichtetem Ti-Al-Si-Cu/Ti-6Al-4V Verbundwerkstoff
    Naidoo, L. C.
    Fatoba, O. S.
    Akinlabi, S. A.
    Mahamood, R. M.
    Shatalov, M. Y.
    Murashkin, E. V.
    Hassan, S.
    Akinlabi, E. T.
    MATERIALWISSENSCHAFT UND WERKSTOFFTECHNIK, 2020, 51 (06) : 766 - 773
12345