Influence of Cutting Speed on Flank Temperature during Face Milling of Magnesium Alloy

被引：35

作者：

Hou, Junzhan ^{[1
,2
]}

Zhao, Ning ^{[2
]}

Zhu, Shaoli ^{[1
]}

机构：

[1] Nanyang Technol Univ, Sch Mech & Aerosp Engn, Singapore 639798, Singapore

[2] Northwestern Polytech Univ, Sch Mech Engn, Xian, Shannxi Provinc, Peoples R China

来源：

MATERIALS AND MANUFACTURING PROCESSES | 2011年 / 26卷 / 08期

关键词：

AM50A magnesium alloy; Cutting speed; Face milling; Mean flank temperature;

D O I：

10.1080/10426914.2010.536927

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Chip ignition is one of the important problems in cutting magnesium alloy due to cutting temperature rise, which is mainly caused by the increase of cutting speed. In this article, we measured the mean flank temperature through mounting two K-type thermocouples in workpiece of AM50A magnesium alloy. Effect of cutting speed on the temperature rise of tool flank was analyzed. The results show that the temperature first increases and then decreases as the cutting speed increases. The chip ignition appears when the mean flank temperature rise is about 3 degrees C in cutting magnesium alloy at ambient temperature. However, the ignition cannot be observed with further increase in temperature. The results can reasonably be used to predict and avoid the occurrence of chip ignition.

引用

页码：1059 / 1063

页数：5

共 19 条

[1] Nd:YAG Laser Welding of AZ91 Magnesium Alloy for Aerospace Industries [J].

Abderrazak, Kamel ;

Ben Salem, Wacef ;

Mhiri, Hatem ;

Bournot, Philippe ;

Autric, Michel .

METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE, 2009, 40 (01) :54-61

[2] Chip control in finish cutting of magnesium alloy [J].

Arai, M ;

Sato, S ;

Ogawa, M ;

Shikata, H .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 1996, 62 (04) :341-344

[3]

Arndt G., 1973, P I MECH ENG, V187, P625, DOI [10.1243/PIME_PROC_1973_187_048_02, DOI 10.1243/PIME_PROC_1973_187_048_02]

[4] Continuous wave Nd:YAG laser welding of sand-cast ZE41A-T5 magnesium alloys [J].

Cao, X ;

Xiao, M ;

Jahazi, M ;

Immarigeon, JP .

MATERIALS AND MANUFACTURING PROCESSES, 2005, 20 (06) :987-1004

[5] Magnesium alloy applications in automotive structures [J].

Easton, Mark ;

Beer, Aiden ;

Barnett, Matthew ;

Davies, Chris ;

Dunlop, Gordon ;

Durandet, Yvonne ;

Blacket, Stuart ;

Hilditch, Tim ;

Beggs, Peter .

JOM, 2008, 60 (11) :57-62

[6] Mean flank temperature measurement in high speed dry cutting of magnesium alloy [J].

Fang, FZ ;

Lee, LC ;

Liu, XD .

JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2005, 167 (01) :119-123

[7]

Friemuth T, 1999, ADV ENG MATER, V1, P183, DOI 10.1002/(SICI)1527-2648(199912)1:3/4<183::AID-ADEM183>3.0.CO

[8]

2-V

[9] Influence of reinforcement and processing on the wear response of two magnesium alloys [J].

Jayamathy, M ;

Seshan, S ;

Kailas, SV ;

Kumar, K ;

Srivatsan, TS .

MATERIALS AND MANUFACTURING PROCESSES, 2005, 20 (02) :255-271

[10] The influence of feed rate and cutting speed on the cutting forces, surface roughness and tool-chip contact length during face milling [J].

Korkut, I. ;

Donertas, M. A. .

MATERIALS & DESIGN, 2007, 28 (01) :308-312

← 1 2 →