Numerical Study of Effect of Sawtooth Riblets on Low-Reynolds-Number Airfoil Flow Characteristic and Aerodynamic Performance

被引:5
作者
Yang, Xiaopei [1 ]
Wang, Jun [1 ]
Jiang, Boyan [1 ]
Li, Zhi'ang [1 ]
Xiao, Qianhao [1 ]
机构
[1] Huazhong Univ Sci & Technol, Sch Energy & Power Engn, Luoyu Rd 1037, Wuhan 430074, Peoples R China
关键词
airfoil; riblets; computational fluid dynamics; drag reduction; DRAG REDUCTION; TURBULENT-FLOW; SIMULATION; SURFACES;
D O I
10.3390/pr9122102
中图分类号
TQ [化学工业];
学科分类号
0817 ;
摘要
Riblets with an appropriate size can effectively restrain turbulent boundary layer thickness and reduce viscous drag, but the effects of riblets strongly depend on the appearance of the fabric that is to be applied and its operating conditions. In this study, in order to improve the aerodynamic performance of a low-pressure fan by using riblet technology, sawtooth riblets on NACA4412 airfoil are examined at the low Reynolds number of 1 x 10(5), and the airfoil is operated at angles of attack (AOAs) ranging from approximately 0 degrees to 12 degrees. The numerical simulation is carried out by employing the SST k-omega turbulence model through the Ansys Fluent, and the effects of the riblets' length and height on aerodynamic performance and flow characteristics of the airfoil are investigated. The results indicate that the amount of drag reduction varies greatly with riblet length and height and the AOA of airfoil flow. By contrast, the riblets are detrimental to the airfoil in some cases. The most effective riblet length is found to be a length of 0.8 chord, which increases the lift and reduces the drag under whole AOA conditions, and the maximum improvements in both are 17.46% and 15.04%, respectively. The most effective height for the riblet with the length of 0.5 chord is 0.6 mm. This also improves the aerodynamic performance and achieves a change rate of 12.67% and 14.8% in the lift and drag coefficients, respectively. In addition, the riblets facilitate a greater improvement in airfoil at larger AOAs. The flow fields demonstrate that the riblets with a drag reduction effect form "the antifriction-bearing" structure near the airfoil surface and effectively restrain the trailing separation vortex. The ultimate cause of the riblet drag reduction effect is the velocity gradient at the bottom of the boundary layers being increased by the riblets, which results in a decrease in boundary thickness and energy loss.
引用
收藏
页数:18
相关论文
共 29 条
  • [11] DIRECT NUMERICAL-SIMULATION OF TURBULENT-FLOW OVER A MODELED RIBLET COVERED SURFACE
    GOLDSTEIN, D
    HANDLER, R
    SIROVICH, L
    [J]. JOURNAL OF FLUID MECHANICS, 1995, 302 : 333 - 376
  • [12] Han M, P TRANSDUCERS SOL ST
  • [13] Three-dimensional measurement of turbulent flow over a riblet surface
    Hou, Jianfeng
    Hokmabad, Babak Vajdi
    Ghaemi, Sina
    [J]. EXPERIMENTAL THERMAL AND FLUID SCIENCE, 2017, 85 : 229 - 239
  • [14] Hough G. R., 1980, PROGR ASTRONAUTICS A, V72, P168
  • [15] Effect of Flow Rate on Turbulence Dissipation Rate Distribution in a Multiphase Pump
    Huang, Zongliu
    Shi, Guangtai
    Liu, Xiaobing
    Wen, Haigang
    [J]. PROCESSES, 2021, 9 (05)
  • [16] Biomimetic structures for fluid drag reduction in laminar and turbulent flows
    Jung, Yong Chae
    Bhushan, Bharat
    [J]. JOURNAL OF PHYSICS-CONDENSED MATTER, 2010, 22 (03)
  • [17] Effect of Tip Clearance Size on Tubular Turbine Leakage Characteristics
    Li, Xinrui
    Li, Zhenggui
    Zhu, Baoshan
    Wang, Weijun
    [J]. PROCESSES, 2021, 9 (09)
  • [18] NEUMANN D, 1991, APPL SCI RES, V48, P105, DOI 10.1007/BF01998668
  • [19] Ng J.H, 2016, ADV COMPUTATION MODE
  • [20] Drag Reduction Using Riblet Film Applied to Airfoils for Wind Turbines
    Sareen, Agrim
    Deters, Robert W.
    Henry, Steven P.
    Selig, Michael S.
    [J]. JOURNAL OF SOLAR ENERGY ENGINEERING-TRANSACTIONS OF THE ASME, 2014, 136 (02):