Performance evaluation of DLC and NCD coatings in micro-milling of Al7075-T6 alloy

被引:17
|
作者
Aslantas, Kubilay [1 ]
Hascelik, Ahmet [1 ]
Cicek, Adem [2 ]
机构
[1] Afyon Kocatepe Univ, Dept Mech Engn, Afyon, Turkey
[2] Ankara Yildirim Beyazit Univ, Dept Mech Engn, Ankara, Turkey
关键词
Micro; -milling; DLC coating; NCD coating; Surface roughness; Burr width; DIAMOND COATINGS; CUTTING PERFORMANCE; SURFACE-ROUGHNESS; ALUMINUM; WEAR; MECHANISMS; THICKNESS; ADHESION; TOOLS; STATE;
D O I
10.1016/j.jmapro.2022.07.053
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
The main problem in machining of aluminum alloys is the adhesion of chips to the cutting tool. In micro milling, chip adhesion causes a decrease in surface quality and contributes to micro burr formation. There are several ways to minimize chip adhesion, one of which is to coat the tool with the appropriate material. Carbon-based coatings are coating materials that can minimize chip adhesion. In this study, the performances of Diamond -Like Carbon (DLC) and Nano-Crystalline Diamond (NCD) coating materials in the micro-milling process of Al7075-T6 alloy were investigated in all aspects. The tests are performed under dry cutting conditions using various cutting parameters. Experimental results show that DLC and NCD coated tools produce approximately 20 % and 40 % lower forces, respectively. For fz < 0.5 mu m/tooth, no decisive influence of the coating material on the cutting forces is observed. For fz < 0.5 mu m/tooth, surface roughness and burr width increase significantly in uncoated and NCD coated tools due to size effect. A strong size effect was observed at feed values less than approximately 36 % of the tool edge radius in terms of surface roughness and <18 % of the tool edge radius in terms of burr width.
引用
收藏
页码:976 / 990
页数:15
相关论文
共 50 条
  • [31] The mechanism of anisotropic micro-milling properties in additively manufactured Ti-6Al-4V alloy
    Tian, Shenglin
    Wang, Zhanfeng
    Wang, Zhao
    Luo, Kaiyu
    Lu, Jinzhong
    JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2023, 322
  • [32] Investigation on Micro-milling of Ti-6Al-4V Alloy by PCD Slotting-Tools
    Han, Jinjin
    Hao, Xiuqing
    Li, Liang
    Zhong, Li
    Zhao, Guolong
    He, Ning
    INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING, 2020, 21 (02) : 291 - 300
  • [33] Influence of cutting conditions on surface characteristics in micro-milling of Ti-6Al-7Nb alloy
    Leo Kumar S.P.
    Avinash D.
    Materials and Manufacturing Processes, 2019, 34 (16) : 1783 - 1791
  • [34] Surface hardness prediction of CrN thin film coating on AL7075-T6 alloy using fuzzy logic system
    Erfan Zalnezhad
    Ahmed Aly Diaa Mohammed Sarhan
    Mohd Hamdi
    International Journal of Precision Engineering and Manufacturing, 2013, 14 : 467 - 473
  • [35] Research on Parameter Optimization of Micro-Milling Al7075 Based on Edge-Size-Effect
    Chen, Yinghua
    Wang, Tao
    Zhang, Guoqing
    MICROMACHINES, 2020, 11 (02)
  • [36] Prediction of cutting force based on machining parameters on AL7075-T6 aluminum alloy by response surface methodology in end millingAbschatzung der Schneidkrafte in Abhangigkeit der Maschinenparameter der Aluminiumlegierung Al7075-T6 durch Antwortflachenmethode beim Endfrasen
    Sethupathy, A.
    Shanmugasundaram, N.
    MATERIALWISSENSCHAFT UND WERKSTOFFTECHNIK, 2021, 52 (08) : 879 - 890
  • [37] Surface hardness prediction of CrN thin film coating on AL7075-T6 alloy using fuzzy logic system
    Zalnezhad, Erfan
    Sarhan, Ahmed Aly Diaa Mohammed
    Hamdi, Mohd
    INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING, 2013, 14 (03) : 467 - 473
  • [38] Stress Analysis of Switchover Module with Al6061-T6 and Al7075-T6 for Hybrid Locomotion Mobile Robot
    Hasnan, Khalid
    Bakhsh, Qadir
    Das, Bhagwan
    Ahmed, Aftab
    Ahmed, Aqeel
    2016 INTERNATIONAL CONFERENCE ON FRONTIERS OF SENSORS TECHNOLOGIES (ICFST 2016), 2016, 59
  • [39] Prediction of TiN coating adhesion strength on aerospace AL7075-T6 alloy using fuzzy rule based system
    Erfan Zalnezhad
    Ahmed Aly Diaa Mohammed Sarhan
    Mohd Hamdi
    International Journal of Precision Engineering and Manufacturing, 2012, 13 : 1453 - 1459
  • [40] Prediction of TiN coating adhesion strength on aerospace AL7075-T6 alloy using fuzzy rule based system
    Zalnezhad, Erfan
    Sarhan, Ahmed Aly Diaa Mohammed
    Hamdi, Mohd
    INTERNATIONAL JOURNAL OF PRECISION ENGINEERING AND MANUFACTURING, 2012, 13 (08) : 1453 - 1459