Performance evaluation of DLC and NCD coatings in micro-milling of Al7075-T6 alloy

被引:17
|
作者
Aslantas, Kubilay [1 ]
Hascelik, Ahmet [1 ]
Cicek, Adem [2 ]
机构
[1] Afyon Kocatepe Univ, Dept Mech Engn, Afyon, Turkey
[2] Ankara Yildirim Beyazit Univ, Dept Mech Engn, Ankara, Turkey
关键词
Micro; -milling; DLC coating; NCD coating; Surface roughness; Burr width; DIAMOND COATINGS; CUTTING PERFORMANCE; SURFACE-ROUGHNESS; ALUMINUM; WEAR; MECHANISMS; THICKNESS; ADHESION; TOOLS; STATE;
D O I
10.1016/j.jmapro.2022.07.053
中图分类号
T [工业技术];
学科分类号
08 ;
摘要
The main problem in machining of aluminum alloys is the adhesion of chips to the cutting tool. In micro milling, chip adhesion causes a decrease in surface quality and contributes to micro burr formation. There are several ways to minimize chip adhesion, one of which is to coat the tool with the appropriate material. Carbon-based coatings are coating materials that can minimize chip adhesion. In this study, the performances of Diamond -Like Carbon (DLC) and Nano-Crystalline Diamond (NCD) coating materials in the micro-milling process of Al7075-T6 alloy were investigated in all aspects. The tests are performed under dry cutting conditions using various cutting parameters. Experimental results show that DLC and NCD coated tools produce approximately 20 % and 40 % lower forces, respectively. For fz < 0.5 mu m/tooth, no decisive influence of the coating material on the cutting forces is observed. For fz < 0.5 mu m/tooth, surface roughness and burr width increase significantly in uncoated and NCD coated tools due to size effect. A strong size effect was observed at feed values less than approximately 36 % of the tool edge radius in terms of surface roughness and <18 % of the tool edge radius in terms of burr width.
引用
收藏
页码:976 / 990
页数:15
相关论文
共 50 条
  • [1] Force Prediction and Cutting-Parameter Optimization in Micro-Milling Al7075-T6 Based on Response Surface Method
    Zhou, Menghua
    Chen, Yinghua
    Zhang, Guoqing
    MICROMACHINES, 2020, 11 (08)
  • [2] Influence of milling strategy on the surface roughness in ball end milling of the aluminum alloy Al7075-T6
    Vakondios, Dimitrios
    Kyratsis, Panagiotis
    Yaldiz, Suleyman
    Antoniadis, Aristomenis
    MEASUREMENT, 2012, 45 (06) : 1480 - 1488
  • [3] Cutting performance of nano-crystalline diamond (NCD) coating in micro-milling of Ti6Al4V alloy
    Aslantas, K.
    Hopa, H. E.
    Percin, M.
    Ucun, I.
    Cicek, A.
    PRECISION ENGINEERING-JOURNAL OF THE INTERNATIONAL SOCIETIES FOR PRECISION ENGINEERING AND NANOTECHNOLOGY, 2016, 45 : 55 - 66
  • [4] CONSTITUTIVE MODEL CONSTANTS FOR Al7075-T651 and Al7075-T6
    Brar, N. S.
    Joshi, V. S.
    Harris, B. W.
    SHOCK COMPRESSION OF CONDENSED MATTER - 2009, PTS 1 AND 2, 2009, 1195 : 945 - +
  • [5] Investigations on effect of nanofluid based minimum quantity lubrication technique for surface milling of Al7075-T6 aerospace alloy
    Kulkarni, Harshit B.
    Nadakatti, Mahantesh M.
    Kulkarni, Sachin C.
    Kulkarni, Raviraj M.
    MATERIALS TODAY-PROCEEDINGS, 2020, 27 : 251 - 256
  • [6] Performance evaluation of a hybrid cooling-lubrication system in micro-milling of Ti6Al4V alloy
    Aslantas, K.
    Cicek, A.
    Ucun, I.
    Percin, M.
    Hopa, H. E.
    7TH HPC 2016 - CIRP CONFERENCE ON HIGH PERFORMANCE CUTTING, 2016, 46 : 492 - 495
  • [7] A Study on Surface Modification of Al7075-T6 Alloy against Fretting Fatigue Phenomenon
    Mohseni, E.
    Zalnezhad, E.
    Sarhan, Ahmed A. D.
    Bushroa, A. R.
    ADVANCES IN MATERIALS SCIENCE AND ENGINEERING, 2014, 2014
  • [8] Construction of a predictive model for residual stresses in micro-milling of 7075 aluminum alloy
    Ping Zhang
    Songting Zhang
    Shunxiang Wang
    Yajie Sun
    Xiujie Yue
    The International Journal of Advanced Manufacturing Technology, 2024, 131 : 3871 - 3883
  • [9] Measurement and analysis of radial force, radial torque and surface integrity in micro-drilling of an Al7075-T6 alloy
    Shukla, Shashank
    Jain, Rahul
    Gangopadhyay, Soumya
    PROCEEDINGS OF THE INSTITUTION OF MECHANICAL ENGINEERS PART B-JOURNAL OF ENGINEERING MANUFACTURE, 2024, 238 (08) : 1183 - 1195
  • [10] Construction of a predictive model for residual stresses in micro-milling of 7075 aluminum alloy
    Zhang, Ping
    Zhang, Songting
    Wang, Shunxiang
    Sun, Yajie
    Yue, Xiujie
    INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2024, 131 (7-8): : 3871 - 3883