Development of an empirical model for predicting the effects of controllable blasting parameters on flyrock distance in surface mines

被引:115
|
作者
Ghasemi, Ebrahim [1 ]
Sari, Mehmet [2 ]
Ataei, Mohammad [1 ]
机构
[1] Shahrood Univ Technol, Dept Min Petr & Geophys Engn, Shahrood, Iran
[2] Aksaray Univ, Dept Min Engn, TR-68100 Aksaray, Turkey
关键词
Flyrock distance; Controllable blasting parameters; Dimensional analysis; Stochastic modeling; Monte Carlo (MC) method; Sensitivity analysis; MONTE-CARLO; FUZZY MODEL; UNCERTAINTY; TRANSPORT; STRENGTH;
D O I
10.1016/j.ijrmms.2012.03.011
中图分类号
P5 [地质学];
学科分类号
0709 ; 081803 ;
摘要
Prediction of flyrock distance has a remarkable role in reduction and control of blasting accident in surface mines. In this paper, at first a new empirical equation for predicting flyrock distance was developed using dimensional analysis. The equation extended based on controllable blasting parameters that compiled from 150 blasting events in Sungun copper mine, Iran. Then, flyrock phenomenon is simulated using this equation and Monte Carlo (MC) method. Results showed that MC is a good means for modeling and assessing the variability of blasting parameters. Finally, sensitivity analysis was conducted to analyze the effects of the controllable blasting parameters on flyrock distance. Based on correlation sensitivity, the most effective parameters were powder factor, stemming and burden. Finally, it should be noted that the proposed flyrock equation and obtained results are site-specific; it should be used only in the Sungun copper mine, and it should not be used directly in other surface mines. (C) 2012 Elsevier Ltd. All rights reserved.
引用
收藏
页码:163 / 170
页数:8
相关论文
共 50 条
  • [31] Development of an air attenuation model for noise prediction in surface mines and quarries
    Pathak, K
    Durucan, S
    Korre, A
    ENVIRONMENTAL ISSUES AND MANAGEMENT OF WASTE IN ENERGY AND MINERAL PRODUCTION, 2000, : 717 - 724
  • [32] PREDICTING DENGUE FEVER OUTBURSTS IN BRAZIL: AN EMPIRICAL MODEL BASED ON CLIMATIC PARAMETERS
    Fahham, L.
    Ueda, A.
    Teich, V
    VALUE IN HEALTH, 2017, 20 (09) : A856 - A856
  • [33] An Optimized Model for Blasting Parameters in Underground Mines' Deep-hole Caving Based on Rough Set and Artificial Neural Network
    Jiang, Fuliang
    Zhou, Keping
    Deng, Hongwei
    Li, Xiangyang
    Zhong, Yongming
    SECOND INTERNATIONAL SYMPOSIUM ON COMPUTATIONAL INTELLIGENCE AND DESIGN, VOL 1, PROCEEDINGS, 2009, : 459 - 462
  • [34] Development of a novel empirical approach to control overbreak, surface quality, and slope angle of benches following blasting
    Soltanalinejad, Sina
    Moomivand, Hassan
    CANADIAN GEOTECHNICAL JOURNAL, 2025, 62 : 24 - 24
  • [35] Development and Assessment of a New Empirical Model for Predicting Full Creep Curves
    Gray, Veronica
    Whittaker, Mark
    MATERIALS, 2015, 8 (07): : 4582 - 4592
  • [36] Development of a multivariate empirical model for predicting weak rock mass modulus
    Kallu Raj R.
    Keffeler Evan R.
    Watters Robert J.
    Agharazi Alireza
    InternationalJournalofMiningScienceandTechnology, 2015, 25 (04) : 545 - 552
  • [37] Development of a multivariate empirical model for predicting weak rock mass modulus
    Raj, Kallu R.
    Evan, Keffeler R.
    Robert, Watters J.
    Alireza, Agharazi
    INTERNATIONAL JOURNAL OF MINING SCIENCE AND TECHNOLOGY, 2015, 25 (04) : 545 - 552
  • [38] Development of a new Blast Vibration prediction Model incorporating Burden Variations in surface Blasting
    Ramulu, M.
    INTERNATIONAL JOURNAL OF GEOTECHNICAL EARTHQUAKE ENGINEERING, 2010, 1 (02) : 72 - 88
  • [39] Surface roughness in final turning: Development of an adequate empirical model
    Bokov V.B.
    Russian Engineering Research, 2016, 36 (7) : 559 - 564
  • [40] Development of an Empirical Model for Optimization of Machining Parameters to Minimize Power Consumption
    Garg, Girish Kant
    Garg, Suman
    Sangwan, K. S.
    INTERNATIONAL CONFERENCE ON RECENT ADVANCES IN MATERIALS & MANUFACTURING TECHNOLOGIES, 2018, 346