Optimal design on SAW sensor for wireless pressure measurement based on reflective delay line

被引：58

作者：

Wang, Wen ^{[1
]}

Lee, Keekeun ^{[1
]}

Woo, Insang ^{[1
]}

Park, Ikmo ^{[1
]}

Yang, Sangsik ^{[1
]}

机构：

[1] Ajou Univ, Div Elect Engn, Akron 443749, South Korea

来源：

SENSORS AND ACTUATORS A-PHYSICAL | 2007年 / 139卷 / 1-2期

关键词：

coupling of modes; reflectors; SAW reflective delay line; SPUDT wireless pressure sensor;

D O I：

10.1016/j.sna.2006.10.018

中图分类号：

TM [电工技术]; TN [电子技术、通信技术];

学科分类号：

0808 ; 0809 ;

摘要：

This paper presents optimal design on wireless pressure micro-sensor based on surface acoustic wave (SAW) reflective delay line. Using the coupling-of-modes (COM) analysis, the device was simulated, and the effect of reflector configuration and interdigital transducer (IDT) structure on the performance of the devices was studied. From the COM simulation results, a 440MHz SAW-based pressure sensor based on a reflective delay line on 4 V YX LiNbO3 with shorted circuit grating reflectors and single-phase unidirectional transducers (SPUDT) structure was developed experimentally. Using the network analyzer, the SAW sensor was wirelessly characterized, and the experiment results were well matched with simulation data. Sharp reflection peaks, low insertion loss and few spurious signals between the peaks were observed. Obtained pressure sensitivity was 2.67 degrees/kPa. (c) 2006 Elsevier B.V. All rights reserved.

引用

页码：2 / 6

页数：5

共 50 条

[1] Quartz pressure sensor based on SAW reflective delay line
Scherr, H
Scholl, G
Seifert, F
Weigel, R
1996 IEEE ULTRASONICS SYMPOSIUM, PROCEEDINGS, VOLS 1 AND 2, 1996, : 347 - 350
[2] SENSITIVITY IMPROVEMENT OF WIRELESS PRESSURE SENSOR BY INCORPORATING A SAW REFLECTIVE DELAY LINE
Oh, Haekwan
Wang, Weng
Lee, Keekeun
Park, Ikmo
Yang, Sang Sik
INTERNATIONAL JOURNAL ON SMART SENSING AND INTELLIGENT SYSTEMS, 2008, 1 (04): : 940 - 954
[3] Simulation and design on SAW reflective delay line for wireless sensor application using coupling of modes
ZHANG Yanhua~1 XU Fangqian~1 WANG Wen~2 (1 Zhejiang University of Media and Communication Zhejiang 310018) (2 Institute of Acoustics
ChineseJournalofAcoustics, 2011, 30 (03) : 272 - 278
[4] Simultaneous and Wireless measurement of CO2 and Humidity using a SAW reflective delay line
Lim, Chunbae
Wang, Wen
Lee, Keekeun
Oh, Hae-Kwan
Yang, Sangsik
MICROFLUIDICS, BIOMEMS, AND MEDICAL MICROSYSTEMS VII, 2009, 7207
[5] A novel wireless passive SAW sensor based on the delay line theory
Li, Tian L.
Zheng, Liang
Hu, Hong
2008 3RD IEEE INTERNATIONAL CONFERENCE ON NANO/MICRO ENGINEERED AND MOLECULAR SYSTEMS, VOLS 1-3, 2008, : 467 - +
[6] SAW Force Sensor Based on Reflective Delay Line Quasi-Mirror Topology
Antcev, Ivan
Bogoslovsky, Sergei
Sapozhnikov, Gennadiy
Zhgoon, Sergei
2015 IEEE INTERNATIONAL ULTRASONICS SYMPOSIUM (IUS), 2015,
[7] Functional passive sensor system using reflective SAW delay line
Nomura, T.
Kosaka, T.
Saitoh, A.
MATERIAL AND DEVICES FOR SMART SYSTEMS II, 2006, 888 : 173 - +
[8] Maximum Measurement Range and Accuracy of SAW Reflective Delay Line Sensors
Zheng, Zehua
Han, Tao
Qin, Peng
SENSORS, 2015, 15 (10) : 26643 - 26653
[9] A Wireless Passive SAW Delay Line Temperature and Pressure Sensor for Monitoring Water Distribution System
Tang, Zhaozhao
Wu, Wenyan
Gao, Jinliang
2018 IEEE SENSORS, 2018, : 144 - 147
[10] Passive strain sensor using SH-SAW reflective delay line
Nomura, T.
Kosaka, T.
Saitoh, A.
Furukawa, S.
FERROELECTRICS, 2006, 333 : 121 - 129

← 1 2 3 4 5 →