Prediction of surface roughness and tool wear in milling process on brass (C26130) alloy by Taguchi technique

被引：13
作者：
Alagarsamy, S. V. [1 ]
Ravichandran, M. [2 ]
Meignanamoorthy, M. [3 ]
Sakthivelu, S. [4 ]
Dineshkumar, S. [5 ]
机构：
[1] Mahath Amma Inst Engn & Technol, Dept Mech Engn, Pudukkottai, India
[2] K Ramakrishnan Coll Engn, Dept Mech Engn, Tiruchirappalli, India
[3] Mother Terasa Coll Engn & Technol, Dept Mech Engn, Pudukkottai, India
[4] Mountz Coll Engn & Technol, Dept Mech Engn, Pudukkottai, India
[5] Chendhuran Coll Engn & Technol, Dept Mech Engn, Pudukkottai, India
来源：
MATERIALS TODAY-PROCEEDINGS | 2020年 / 21卷
关键词：
Brass (C26130) alloy; End milling; Surface roughness; Tool wear; Taguchi technique; ANOVA; MACHINING PARAMETERS; OPTIMIZATION;
D O I：
10.1016/j.matpr.2019.04.219
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
The machining parameters is optimized during CNC end milling process of brass C26130 alloy using Taguchi technique. The experimental results shows that the combination of 750 rpm spindle speed, 20 mm/rev feed rate and 1 mm depth of cut was identified as the optimum level for minimum surface roughness (SR) and the combination of 750 rpm spindle speed, 60 mm/rev feed rate and 0.75 mm depth of cut was identified as the optimum level for minimum tool wear (TW). ANOVA results revealed that the spindle speed and feed rate was identified as the highest influencing parameters on SR and TW. (C) 2019 Elsevier Ltd. All rights reserved.
引用
收藏
页码：189 / 193
页数：5
相关论文
共 17 条
  • [1] Alagarsamy S.V., 2018, INT J TECHNOCHEM RES, V4, P117
  • [2] Cetin OZ., 2012, ADV NAT APPL SCI, V6, P866
  • [3] Jeyakumar S, 2015, INDIAN J ENG MATER S, V22, P29
  • [4] Pediatric spinal infections
    Kumar, Raj
    Arora, Rajnish
    [J]. INDIAN JOURNAL OF NEUROSURGERY, 2014, 3 (02) : 75 - 85
  • [5] Synthesis, properties and EDM behavior of 10 wt.-% ZrB2 reinforced AA7178 matrix composites
    Kumar, Sundaram Dinesh
    Ravichandran, Manickam
    [J]. MATERIALS TESTING, 2018, 60 (09) : 877 - 884
  • [6] Investigation of the effect of machining parameters on the surface quality of machined brass (60/40) in CNC end milling-ANFIS modeling
    Maher, Ibrahem
    Eltaib, M. E. H.
    Sarhan, Ahmed A. D.
    El-Zahry, R. M.
    [J]. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2014, 74 (1-4) : 531 - 537
  • [7] Optimal Selection of process parameters in CNC end milling of Al 7075-T6 aluminium alloy using a Taguchi-Fuzzy approach
    Mahesh, Thakur Paramjit
    Rajesh, R.
    [J]. INTERNATIONAL CONFERENCE ON ADVANCES IN MANUFACTURING AND MATERIALS ENGINEERING (ICAMME 2014), 2014, 5 : 2493 - 2502
  • [8] Optimization of Machining Parameters for End Milling of Inconel 718 Super Alloy Using Taguchi Based Grey Relational Analysis
    Maiyar, Lohithaksha M.
    Ramanujam, R.
    Venkatesan, K.
    Jerald, J.
    [J]. INTERNATIONAL CONFERENCE ON DESIGN AND MANUFACTURING (ICONDM2013), 2013, 64 : 1276 - 1282
  • [9] Optimization of Abrasive Water Jet Machining Parameters for α-β brass using Taguchi Methodology
    Marichamy, S.
    Ravichandran, M.
    Stalin, B.
    Babu, B. Sridhar
    [J]. FME TRANSACTIONS, 2019, 47 (01): : 116 - 121
  • [10] Parametric optimization of EDM process on α-β brass using Taguchi approach
    Marichamy, S.
    Saravanan, M.
    Ravichandran, M.
    Veerappan, G.
    [J]. RUSSIAN JOURNAL OF NON-FERROUS METALS, 2016, 57 (06) : 586 - 598
12