Effect of encapsulated hot isostatic pressing on properties of Ti6Al4V deposits produced by cold spray

被引：21

作者：

Petrovskiy, P. ^{[1
]}

Travyanov, A. ^{[1
]}

Cheverikin, V. V. ^{[1
]}

Chereshneva, A. A. ^{[1
]}

Sova, A. ^{[2
]}

Smurov, I ^{[1
,2
]}

机构：

[1] Natl Univ Sci & Technol MISIS, Moscow 119049, Russia

[2] Univ Lyon, Natl Engn Sch St Etienne ENISE, LTDS Lab, UMR 5513, F-42100 St Etienne, France

来源：

INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY | 2020年 / 107卷 / 1-2期

关键词：

Cold spray; Hot isostatic pressing; Additive manufacturing; Titanium alloy; ADIABATIC SHEAR INSTABILITY; MECHANICAL-PROPERTIES; MICROSTRUCTURE; ADHESION; COMPONENTS; TI-6AL-4V; COATINGS; REPAIR; HIP; TI;

D O I：

10.1007/s00170-020-05080-9

中图分类号：

TP [自动化技术、计算机技术];

学科分类号：

0812 ;

摘要：

Cold spraying is a new additive manufacturing method capable of producing titanium alloy parts at a high production rate under ambient conditions. In this work, encapsulated hot isostatic pressing (HIP) was applied to reduce the porosity and improve the mechanical properties of cold-sprayed Ti6Al4V deposits. Encapsulated HIP at 110 MPa and 1173 K was found to significantly change the microstructure of the deposits owing to enhanced diffusion and material recrystallization. The total porosity decreased from 7.5 to 0.2%. The measured ultimate tensile strengths of the as-built and HIP-treated samples were similar to 70 and similar to 950 MPa, respectively. The elongation at break also increased, from less than 1% to similar to 13%.

引用

页码：437 / 449

页数：13

共 39 条

[21] Deposition of composite coatings by cold spray using stainless steel 316L, copper and Tribaloy T-700 powder mixtures
Maestracci, R.
Sova, A.
Jeandin, M.
Malhaire, J. -M.
Movchan, I.
Bertrand, Ph.
Smurov, I.
[J]. SURFACE & COATINGS TECHNOLOGY, 2016, 287 : 1 - 8
[22] Maev R.G., 2008, Introduction to Low Pressure Gas Dynamic Spray: Physics Technology
[23] The influence of powder properties on the adhesion strength and microstructural evolution of cold sprayed Ti6Al4V single splats
Munagala, Venkata Naga Vamsi
Imbriglio, Sara I.
Chromik, Richard R.
[J]. MATERIALS LETTERS, 2019, 244 : 58 - 61
[24] Influence of Powder Morphology and Microstructure on the Cold Spray and Mechanical Properties of Ti6Al4V Coatings
Munagala, Venkata Naga Vamsi
Akinyi, Valary
Phuong Vo
Chromik, Richard R.
[J]. JOURNAL OF THERMAL SPRAY TECHNOLOGY, 2018, 27 (05) : 827 - 842
[25] Papyrin A, 2007, WOODHEAD PUBL MATER, P11, DOI 10.1533/9781845693787.1.11
[26] Cold gas dynamic manufacturing: A non-thermal approach to freeform fabrication
Pattison, J.
Celotto, S.
Morgan, R.
Bray, M.
O'Neill, W.
[J]. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2007, 47 (3-4) : 627 - 634
[27] Pin Fin Array Heat Sinks by Cold Spray Additive Manufacturing: Economics of Powder Recycling
Perry, J.
Richer, P.
Jodoin, B.
Matte, E.
[J]. JOURNAL OF THERMAL SPRAY TECHNOLOGY, 2019, 28 (1-2) : 144 - 160
[28] Influence of hot isostatic pressing on structure and properties of titanium cold-spray deposits
Petrovskiy, P.
Sova, A.
Doubenskaia, M.
Smurov, I.
[J]. INTERNATIONAL JOURNAL OF ADVANCED MANUFACTURING TECHNOLOGY, 2019, 102 (1-4) : 819 - 827
[29] Cold gas dynamic spray additive manufacturing today: Deposit possibilities, technological solutions and viable applications
Raoelison, R. N.
Verdy, Ch.
Liao, H.
[J]. MATERIALS & DESIGN, 2017, 133 : 266 - 287
[30] Characterization of heat treatment-induced pore structure changes in cold-sprayed titanium
Ren, Y. Q.
King, P. C.
Yang, Y. S.
Xiao, T. Q.
Chu, C.
Gulizia, S.
Murphy, A. B.
[J]. MATERIALS CHARACTERIZATION, 2017, 132 : 69 - 75

← 1 2 3 4 →