Microstructural Investigation Of Ti Coating On Ti6al4v By Laser Cladding

被引：2

作者：

Sobiyi, Kehinde ^{[1
]}

Akinlabi, Esther ^{[1
]}

机构：

[1] Univ Johannesburg, Dept Mech Engn Sci, ZA-2006 Johannesburg, South Africa

来源：

MATERIALS TODAY-PROCEEDINGS | 2017年 / 4卷 / 02期

关键词：

titanium; laser cladding; porosity; scanning speed; TITANIUM; ALLOYS;

D O I：

暂无

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Understanding the effect of processing parameters is vital in controlling the properties of the final product fabricated from the laser cladding process. The objective of the paper is to characterize the influence of laser scanning speed of laser cladding of commercially pure titanium powder on Ti6Al4V at different scanning speeds. The results obtained showed that the clad height, width and porosity generally reduce as the scanning speed increases. The microstructure of the clad zone is of Widmanstatten structure in nature, the heat affected zone is acicular martensitic in nature, indicating a single beta phase, resulting from the temperature at this zone exceeding the critical point of the Ti6Al4V alloy substrate. The formation of titanium alloys was observed in the cladding zone, with a rich Ti phase. The deposited Ti powder reacts with both Al and V from the substrate, resulting from high affinity of Ti for both Al and V and diffusion of these elements from the substrate into the molten powder during laser cladding process. The average hardness was found to increase with an increase in scanning speed for all samples investigated, with the microhardness at the coatings is lower than that of the substrate material. (C) 2017 Elsevier Ltd. All rights reserved.

引用

页码：244 / 249

页数：6

共 11 条

[1] Microstructure and corrosion behaviour of laser metal deposited Ti6Al4V/Cu composites in 3.5% sea water [J].

Erinosho, Mutiu F. ;

Akinlabi, Esther T. ;

Pityana, Sisa .

MATERIALS TODAY-PROCEEDINGS, 2015, 2 (4-5) :1166-1174

[2] The titanium image: Facing the realities of life [J].

Froes, FH .

JOM-JOURNAL OF THE MINERALS METALS & MATERIALS SOCIETY, 2000, 52 (05) :12-12

[3] Effect of powder state on spark plasma sintering of TiAl alloys [J].

Guyon, J. ;

Hazotte, A. ;

Monchoux, J. P. ;

Bouzy, E. .

INTERMETALLICS, 2013, 34 :94-100

[4]

Kusmoko A., 2014, Procedia Materials Science, V6, P26, DOI [10.1016/j.mspro.2014.07.005, DOI 10.1016/J.MSPRO.2014.07.005, 10.1016/j.mspro.2014.07, DOI 10.1016/J.MSPRO.2014.07]

[5]

Kusmoko A., 2013, ADV MAT MANUF CHARAC, V2, P469

[6]

MAHAMOOD R.M., 2013, Proceedings of the International Multi-Conference of Engineers and Computer Scientists, V2

[7] Scanning velocity influence on microstructure, microhardness and wear resistance performance of laser deposited Ti6Al4V/TiC composite [J].

Mahamood, Rasheedat M. ;

Akinlabi, Esther T. ;

Shukla, Mukul ;

Pityana, Sisa .

MATERIALS & DESIGN, 2013, 50 :656-666

[8] Laser Cladding of TiC for Better Titanium Components [J].

Sampedro, J. ;

Pereza, I. ;

Carcel, B. ;

Ramos, J. A. ;

Amigo, V. .

LASERS IN MANUFACTURING 2011: PROCEEDINGS OF THE SIXTH INTERNATIONAL WLT CONFERENCE ON LASERS IN MANUFACTURING, VOL 12, PT A, 2011, 12 :313-322

[9] Statistical analysis and optimization of process parameters in Ti6Al4V laser cladding using Nd:YAG laser [J].

Sun, Yuwen ;

Hao, Mingzhong .

OPTICS AND LASERS IN ENGINEERING, 2012, 50 (07) :985-995

[10]

Wanliang W., 2005, J MATER SCI LETT, V22, P1169

← 1 2 →