An extended method for work and heat integration considering practical operating constraints

被引:4
作者
Pavao, Leandro V. [1 ]
Caballero, Jose A. [2 ]
Ravagnani, Mauro A. S. S. [1 ,2 ]
Costa, Caliane B. B. [1 ]
机构
[1] Univ Estadual Maringa, Dept Chem Engn, Av Colombo 5790,Bloco D90, BR-87020900 Maringa, PR, Brazil
[2] Univ Alicante, Inst Chem Proc Engn, Ap Correos 99, E-03080 Alicante, Spain
关键词
Optimization; Work and heat integration; Work and heat exchange networks; Meta-heuristics; Process synthesis; EXCHANGE NETWORK SYNTHESIS; PRESSURE RECOVERY; GRAPHICAL-METHOD; PROCESS STREAMS; PINCH ANALYSIS; DESIGN; COMPRESSORS; FRAMEWORK; ENERGY; SUB;
D O I
10.1016/j.enconman.2020.112469
中图分类号
O414.1 [热力学];
学科分类号
摘要
The development of methodologies for the simultaneous work and heat integration has increasingly been the focus of recent research. Approaches may vary among optimization and heuristic-based methods considering direct and indirect work exchange, in addition to, or with the development of new strategies for heat recovery. This work presents a strategy for the synthesis of work and heat exchange networks (WHEN) considering the use of single-shaft-turbine-compressor (SSTC) units. The method is based on a meta-heuristic approach and aims fundamentally at synthesizing WHEN that may operate within industrial-like conditions, which are often narrower than those considered in the literature due to simplification assumptions. Therefore, in the present work, practical temperature upper/lower-bound constraints are considered for pressure manipulation units, and the number of coupled units per shaft is limited. Evidently, these constraints yield additional difficulties for the optimization method. The method considers inlet and outlet temperatures as decision variables in the units of a block-based model, making the maintenance of solutions within feasible range more efficient during the optimization runs. Moreover, a new Simulated Annealing (SA) based strategy is developed for deciding optimal compressor/turbine couplings in a model that considers a preset number of "slots" per shaft. The method aims at minimizing total annual costs (TAC) and is tested over four case studies. The first two are used both as benchmark for TAC comparison to those reported in the literature as well as for testing the new constraints. The other two cases are investigated for TAC and energy-wise improvements to original designs. Considerable economic improvements and better use of energy are attained in all cases. For the two benchmark studies, solutions with TAC 1.5% and 4.3% lower than literature designs were found. For the industrial cases, energy requirements were overall reduced. For instance, in example 3, no external power source is required, while literature solutions present power shortage. In example 4, compression power requirements were reduced by 9.9%. The method also proved efficient in maintaining solutions within practical operating ranges.
引用
收藏
页数:17
相关论文
共 50 条
  • [41] An enhanced superstructure-based model for work-integrated heat exchange network considering inter-stage multiple utilities optimization
    Zhuang, Yu
    Xing, Yafeng
    Zhang, Lei
    Liu, Linlin
    Du, Jian
    Shen, Shengqiang
    COMPUTERS & CHEMICAL ENGINEERING, 2021, 152
  • [42] Simulating a solar parabolic trough collector plant used for industrial process heat using an optimized operating scheme that utilizes flexible heat integration
    Immonen, Jake
    Mohammadi, Kasra
    Powell, Kody M.
    SOLAR ENERGY, 2022, 236 : 756 - 771
  • [43] Guided Tuning of Turbine Blades: A Practical Method to Avoid Operating at Resonance
    Duong, Loc
    Murphy, Kevin D.
    Kazerounian, Kazem
    JOURNAL OF VIBRATION AND ACOUSTICS-TRANSACTIONS OF THE ASME, 2013, 135 (05):
  • [44] Assisted Heat Transfer and Shaft Work Targets for Increased Total Site Heat Integration
    Walmsley, Timothy G.
    Atkins, Martin J.
    Tarighaleslami, Amir H.
    Liew, Peng Yen
    PRES2016: 19TH INTERNATIONAL CONFERENCE ON PROCESS INTEGRATION, MODELING AND OPTIMIZATION FOR ENERGY SAVINGS AND POLLUTION REDUCTION, 2016, 52 : 403 - 408
  • [45] Optimization of layer patterning on a plate fin heat exchanger considering abnormal operating conditions
    Cho, Du-Hyeon
    Seo, Seung-Kwon
    Lee, Chul-Jin
    Lim, Youngsub
    APPLIED THERMAL ENGINEERING, 2017, 127 : 1036 - 1048
  • [46] Risk-averse multi-objective optimal combined heat and power planning considering voltage security constraints
    Yadegari, Saeed
    Abdi, Hamdi
    Nikkhah, Saman
    ENERGY, 2020, 212
  • [47] Risk-averse multi-objective optimal combined heat and power planning considering voltage security constraints
    Yadegari, Saeed
    Abdi, Hamdi
    Nikkhah, Saman
    ENERGY, 2020, 212
  • [48] Metro Scheduling to Minimize Travel Time and Operating Cost Considering Spatial and Temporal Constraints on Passenger Boarding
    Zhou, Yuhe
    Bai, Yun
    Guo, Haiyang
    Li, Tang
    Qiu, Yu
    Zhang, Zhao
    IEEE ACCESS, 2020, 8 (08) : 114190 - 114210
  • [49] A graph theory-based optimal configuration method of energy hub considering the integration of electric vehicles
    Lyu, Jiawei
    Zhang, Shenxi
    Cheng, Haozhong
    Yuan, Kai
    Song, Yi
    ENERGY, 2022, 243
  • [50] Re-considering product design: a practical "road-map" for integration of sustainability issues
    Waage, Sissel A.
    JOURNAL OF CLEANER PRODUCTION, 2007, 15 (07) : 638 - 649