A novel morphology development of micro-injection molded isotactic polypropylene

被引：6
|
作者：
Wang, Shiwei [1 ]
Wang, Zhenwei [1 ]
Zhao, Na [1 ]
Jiang, Jing [1 ]
Li, Qian [1 ]
机构：
[1] Zhengzhou Univ, Natl Ctr Int Joint Res Micronano Molding Technol, Zhengzhou 450001, Henan, Peoples R China
来源：
RSC ADVANCES | 2015年 / 5卷 / 52期
基金：
中国博士后科学基金;
关键词：
PARTS;
D O I：
10.1039/c5ra04626b
中图分类号：
O6 [化学];
学科分类号：
0703 ;
摘要：
A novel stripe morphology was investigated in a micro-injection molded isotactic polypropylene gear. The annealing treatment was performed on the gear tooth under different temperature and time to control its morphology evolution. This work provides a new way to explore the morphology evolution of micro injection molded products.
引用
收藏
页码：41608 / 41610
页数：3
相关论文
共 50 条
  • [1] Morphology, microstructure and mechanical properties of micro injection molded isotactic polypropylene parts
    Zhang Y.
    Wang L.
    Bian N.
    Wang D.
    Wang Y.
    Li Q.
    Shen C.
    Wang, Lixia (lxwang@zzu.edu.cn), 1600, Sichuan University (32): : 114 - 120
  • [2] Unusual hierarchical structures of micro-injection molded isotactic polypropylene in presence of an in situ microfibrillar network and a β-nucleating agent
    Zhao, Zhongguo
    Yang, Qi
    Kong, Miqiu
    Tang, Dahang
    Chen, Qianying
    Liu, Ying
    Lou, Fangli
    Huang, Yajiang
    Liao, Xia
    RSC ADVANCES, 2015, 5 (54): : 43571 - 43580
  • [3] Mechanical properties of micro injection molded isotactic polypropylene parts
    Zhang, Jianbo
    Wang, Lixia
    Wang, Xinchao
    Liu, Xiaodong
    Jiang, Lin
    Bian, Ning
    Zhang, Yang
    Li, Qian
    Gaofenzi Cailiao Kexue Yu Gongcheng/Polymeric Materials Science and Engineering, 2015, 31 (02): : 124 - 129
  • [4] Morphology and properties of β-nucleated injection molded isotactic polypropylene.
    Varga, J
    Mudra, I
    Ehrenstein, GW
    CONFERENCE PROCEEDINGS AT ANTEC '98: PLASTICS ON MY MIND, VOLS I-3: VOL I; PROCESSING, VOL II; SPECIAL AREAS, VOL III; MATERIALS, 1998, 44 : 3492 - 3496
  • [5] SURFACE MORPHOLOGY OF MOLDED ISOTACTIC POLYPROPYLENE
    FITCHMUN, D
    NEWMAN, S
    BULLETIN OF THE AMERICAN PHYSICAL SOCIETY, 1969, 14 (03): : 365 - &
  • [6] Effect of Quinacridone Pigments on Properties and Morphology of Injection Molded Isotactic Polypropylene
    Barczewski, Mateusz
    Matykiewicz, Danuta
    Hoffmann, Bartlomiej
    INTERNATIONAL JOURNAL OF POLYMER SCIENCE, 2017, 2017
  • [7] Development of β and α isotactic polypropylene polymorphs in injection molded structural foams
    Djoumaliisky, Strashimir
    Luisa Cerrada, Maria
    Dobreva, Tatyana
    Zipper, Peter
    CHEMICAL PAPERS, 2010, 64 (02) : 246 - 254
  • [8] Development of β and α isotactic polypropylene polymorphs in injection molded structural foams
    Strashimir Djoumaliisky
    Maria Luisa Cerrada
    Tatyana Dobreva
    Peter Zipper
    Chemical Papers, 2010, 64 : 246 - 254
  • [9] Effect of mold temperature on the structures and mechanical properties of micro-injection molded polypropylene
    Jiang, Jing
    Wang, Shiwei
    Sun, Bo
    Ma, Shuaijiang
    Zhang, Jianming
    Li, Qian
    Hu, Guo-Hua
    MATERIALS & DESIGN, 2015, 88 : 245 - 251
  • [10] Influence of melt temperature on the morphology evolution of injection molded isotactic polypropylene parts
    Liu, Yan
    Wang, Lixia
    Li, Qian
    Sheng, Changyu
    Jia, Zhenhua
    Gaofenzi Cailiao Kexue Yu Gongcheng/Polymeric Materials Science and Engineering, 2012, 28 (07): : 79 - 82
12345