Removal of Iron from a Secondary Al-Si Die-Casting Alloy by Metal Melt Filtration in a Laboratory Filtration Apparatus

被引：8

作者：

Schoss, Johannes Paul ^{[1
]}

Becker, Hanka ^{[2
]}

Kessler, Andreas ^{[1
]}

Leineweber, Andreas ^{[2
]}

Wolf, Gotthard ^{[1
]}

机构：

[1] TU Bergakad Freiberg, Foundry Inst, D-09599 Freiberg, Germany

[2] TU Bergakad Freiberg, Inst Mat Sci, D-09599 Freiberg, Germany

来源：

ADVANCED ENGINEERING MATERIALS | 2022年 / 24卷 / 02期

关键词：

aluminum alloys; intermetallic phases; iron removal; metal melt filtration; sludge formations; CONTAINING INTERMETALLIC PHASES; RECYCLED ALUMINUM; SLUDGE PARTICLES; FE; ALPHA-AL(FEMN)SI; PRECIPITATION; NUCLEATION; MANGANESE; EVOLUTION; BEHAVIOR;

D O I：

10.1002/adem.202100695

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

The influence of chemical composition and cooling rate is investigated on a secondary die-casting alloy with the aim of reduction of iron using metal melt filtration in a specially developed laboratory filtration apparatus. Based on the defined thermal conditions of the device, differential scanning calorimetry (DSC) cooling curves are determined to obtain formation temperatures of the primary iron-containing intermetallic phases (also called sludge phases) for an EN AC-AlSi9Cu3(Fe) alloy with different contents of Fe, Mn, and Cr. The DSC samples are then analyzed metallographically, and the results are compared with CalPhaD calculations. After that, the temperature of the sludge formation is adjusted using furnace-operating curves to confirm the presence of the intermetallic phases by sedimentation and filtration trials. The Fe content is reduced by about 50%, as shown by chemical analysis based on remelted materials in optical emission spectroscopy. The elements Mn and Cr decrease by approximate to 66% and 86% after filtration at 620 degrees C, respectively.

引用

页数：15

共 50 条

[21] Methodology of Establishing Holding Furnace Characteristic for Al-Si Alloys in Pressure Die-casting Process with Application
Fedak, Marcel
Semanco, Pavol
Rimar, Miroslav
AASRI CONFERENCE ON POWER AND ENERGY SYSTEMS, 2012, 2 : 169 - 173
[22] Tensile properties of Al-Si-Cu die-casting alloy in the partial solidification state
2013, Springer-Verlag (63):
[23] Effect of Casting Die Cooling on Solidification Process and Microstructure of Hypereutectic Al-Si Alloy
Wladysiak, R.
Kozun, A.
Pacyniak, T.
ARCHIVES OF FOUNDRY ENGINEERING, 2016, 16 (04) : 175 - 180
[24] Separation of Refined Silicon from Al-Si Alloys by Air Pressure Filtration
Li, Tianyang
Guo, Lei
Wang, Zhe
Guo, Zhancheng
METALLURGICAL AND MATERIALS TRANSACTIONS B-PROCESS METALLURGY AND MATERIALS PROCESSING SCIENCE, 2019, 50 (03): : 1171 - 1179
[25] Separation of Refined Silicon from Al-Si Alloys by Air Pressure Filtration
Tianyang Li
Lei Guo
Zhe Wang
Zhancheng Guo
Metallurgical and Materials Transactions B, 2019, 50 : 1171 - 1179
[26] Assessment of melt cleanliness and analysis of inclusions in Al-Si alloys using the Prefil pressure filtration technique
Samuel, FH
Ouellet, P
Simard, A
INTERNATIONAL JOURNAL OF CAST METALS RESEARCH, 1999, 12 (01) : 17 - 33
[27] Study on high-temperature wear and mechanism of Al-Si/graphite composites prepared by the die-casting process
Deng, Yafei
Pan, Xiaotao
Zeng, Guoxun
Liu, Jie
Xiao, Sinong
Zhou, Zhenquan
INDUSTRIAL LUBRICATION AND TRIBOLOGY, 2020, 72 (10) : 1153 - 1158
[28] Microstructure and mechanical properties of high strength die-casting Al-wMg-Si-Mn alloy
Hu, Zuqi
Wan, Li
Wu, Shusen
Wu, Han
Liu, Xueqiang
MATERIALS & DESIGN, 2013, 46 : 451 - 456
[29] HYPOEUTECTIC Al-Si ALLOY DOPED WITH CHROMIUM, TUNGSTEN AND MOLYBDENUM DESIGNATED FOR PRESSURE DIE CASTING
Szymczak, T.
Gumienny, G.
Kurowska, B.
Pacyniak, T.
ARCHIVES OF METALLURGY AND MATERIALS, 2017, 62 (03) : 1629 - 1635
[30] Experimental and optimization of die casting parameters on Al-Si alloy with snail shell reinforcing agent
Puspitasari, Poppy
Suprayitno
Nurmalasari, Riana
Pramono, Diki Dwi
Muhlasin, Ainul Kahfi
MATERIALS RESEARCH EXPRESS, 2023, 10 (12)

← 1 2 3 4 5 →