Optimization Analysis of Mechanical Properties of Fly Ash-Based Multicontent Gasification Slag Paste Filling Material

被引:2
|
作者
Chen, Denghong [1 ,2 ]
Cao, Tianwei [1 ,2 ]
Chen, Ran [1 ,2 ]
Li, Chao [1 ,2 ]
机构
[1] Anhui Univ Sci & Technol, Sch Min Engn, Huainan 232001, Peoples R China
[2] Hefei Comprehens Natl Sci Ctr, Inst Energy, Hefei 230031, Anhui, Peoples R China
关键词
D O I
10.1155/2022/5908317
中图分类号
TU [建筑科学];
学科分类号
0813 ;
摘要
In view of the difficult utilization of a large amount of coal-based solid waste produced by coal electrification in the Ningdong mining area, especially the large storage and low utilization rate of gasified slag, combined with the advantages of high paste filling concentration, fast efficiency, and low construction cost, it is of great significance to study the appropriate proportion of fly ash-based multicontent gasified slag paste filling material for green mining and large-amount utilization of gasified slag. Based on the microstructure, composition, and particle size distribution of gasification slag, fly ash, broken coal gangue, furnace bottom slag, and desulfurization gypsum tested by XRD, SEM, and particle size sorting screen, the mass fraction (X-1), gasification slag content (X-2), m (c): m (FA) (X-3). 29 groups of schemes are designed by four factors:mass fraction X-1 refers to the proportion of solid in the filling paste, the amount of gasification slag in the solid X-2 refers to the proportion of gasification slag in the solid, and m(c):m(FA) X-3 refers to the proportion of fly ash and cement in the solid excluding gasification slag, coal gangue, desulfurization gypsum, and furnace bottom slag. The amount of desulfurization gypsum in the solid X-4 refers to the proportion of desulfurization gypsum in the solid. The flow and strength characteristics of each group are analyzed. It is found that before proportioning, coal gangue of 2.5 similar to 5mm accounts for 80.8%, furnace bottom slag of less than 2.5mm accounts for 56.5%, fly ash of 20 similar to 80%mu m accounts for 80%, and fly ash of 10 similar to 20%mu m accounts for 90%. XRD patterns reveal that the main components of four solid wastes and cement are SiO2 and Ca3SiO5, and the chemical composition of desulfurization gypsum is Ca(SO4)(H2O)(2). The regularity of size change tends to be consistent, and the uniaxial compressive strength of 3 days later in group thirteenth exceeds 0.991MPa. Combined with the flow characteristics, it is determined that there are 6 optimization groups in the inclined ladder area with the expansion of 200 similar to 250mm and the uniaxial compressive strength of 0.6 similar to 1.4MPa. The compressive strength increases with the increase of the mass fraction of single-factor analysis. The response surface method of C shows that the significance of X-1, X-2, X-3, and X-4 decreases in turn. The central combination design is used to predict that the mix proportion of X-1 is 84%, X-2 is 15%, X-3 is 1:5, and X-4 is 7%, the content of coal gangue is 10%, and the content of furnace bottom slag is 5% which is the best. The supplementary experimental results show that sigma(3d) is 1.35MPa and the expansion is 200mm. Combined with SEM, it is found that the microstructure before and after optimization is rich in hydration products and the internal structure is well cemented, which further explains sigma(C). The above research provides important basic parameters for large-scale disposal and green filling mining which is difficult to deal with a large amount of stockpiled gasification slag.
引用
收藏
页数:11
相关论文
共 50 条
  • [41] Research on mechanical and electromagnetic shielding properties of cement paste with different contents of fly ash and slag
    Li, Yue
    Liu, Yunze
    Jin, Caiyun
    Mu, Jinlei
    Liu, Jianglin
    NDT & E INTERNATIONAL, 2023, 133
  • [42] Fly ash-based geopolymers with refractoriness properties
    Katarzyna Zarębska
    Piotr Zabierowski
    Magdalena Gazda-Grzywacz
    Natalia Czuma
    Paweł Baran
    Clean Technologies and Environmental Policy, 2022, 24 : 2161 - 2175
  • [43] Mechanical and durability properties of fly ash and slag based geopolymer concrete
    Kurtoglu, Ahmet Emin
    Alzeebaree, Radhwan
    Aljumaili, Omar
    Nis, Anil
    Gulsan, Mehmet Eren
    Humur, Ghassan
    Cevik, Abdulkadir
    ADVANCES IN CONCRETE CONSTRUCTION, 2018, 6 (04) : 345 - 362
  • [44] Effect of PVA fiber on mechanical properties of fly ash-based geopolymer concrete
    Zhang, Peng
    Han, Xu
    Zheng, Yuanxun
    Wan, Jinyi
    Hui, David
    REVIEWS ON ADVANCED MATERIALS SCIENCE, 2021, 60 (01) : 418 - 437
  • [45] Mechanical and fracture properties of fly ash-based geopolymer concrete with different fibers
    Yang, Shiyu
    Zhao, Renda
    Ma, Bonan
    Si, Ruizhe
    Zeng, Xianshuai
    JOURNAL OF BUILDING ENGINEERING, 2023, 63
  • [46] Role of particle size on the mechanical and microstructural properties of fly ash-based geopolymer
    Das, Dipankar
    Interactions, 2024, 245 (01)
  • [47] Effect of curing condition on the mechanical properties of fly ash-based geopolymer concrete
    Hassan, Amer
    Arif, Mohammed
    Shariq, M.
    SN APPLIED SCIENCES, 2019, 1 (12):
  • [48] Effect of slag addition on mechanical properties of fly ash based geopolymers
    Marcin, Michal
    Sisol, Martin
    Brezani, Ivan
    ECOLOGY AND NEW BUILDING MATERIALS AND PRODUCTS 2016, 2016, 151 : 191 - 197
  • [49] Hybrid Fly Ash-Based Geopolymeric Foams: Microstructural, Thermal and Mechanical Properties
    Roviello, Giuseppina
    Ricciotti, Laura
    Molino, Antonio Jacopo
    Menna, Costantino
    Ferone, Claudio
    Asprone, Domenico
    Cioffi, Raffaele
    Ferrandiz-Mas, Veronica
    Russo, Pietro
    Tarallo, Oreste
    MATERIALS, 2020, 13 (13) : 1 - 19
  • [50] Effect of curing condition on the mechanical properties of fly ash-based geopolymer concrete
    Amer Hassan
    Mohammed Arif
    M. Shariq
    SN Applied Sciences, 2019, 1