Investigation of the Effect of Zirconium Amount on Grain Size and Wear Performance in TZM Alloys Produced by Mechanical Alloying Method

被引：1
|
作者：
Sirali, Haktan [1 ]
Simsek, Dogan [2 ]
Ozyurek, Dursun [3 ]
机构：
[1] Karabuk Univ, Inst Sci, Karabuk, Turkey
[2] Natl Def Univ, Army NCO Vocat HE Sch, Balikesir, Turkey
[3] Karabuk Univ, Technol Fac, Karabuk, Turkey
来源：
TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS | 2022年 / 75卷 / 03期
关键词：
TZM alloy; Zirconium; Grain size; Wear; BEHAVIOR;
D O I：
10.1007/s12666-021-02510-4
中图分类号：
TF [冶金工业];
学科分类号：
0806 ;
摘要：
In this study, the relation between grain size, hardness and wear performance of Titanium-Zirconium-Molybdenum (TZM) alloys with different amounts (0.06, 0.07, 0.08 and 0.09 wt%) of Zr added by the mechanical alloying method was investigated. As a result of the studies, it was observed that the number of pores in the structure increased with the increase in the amount of Zr, while there was a decrease in the grain size. In the hardness and density results, it was observed that while the hardness values increased with increasing Zr amount, there was a decrease in the density values. As a result of the wear tests, the lowest weight loss at 10-30 N loads was obtained in the TZM alloy with the highest Zr added (0.09% Zr). The lowest friction coefficient in the friction coefficient results was obtained in TZM alloy with 0.09% Zr added.
引用
收藏
页码：805 / 812
页数：8
相关论文
共 50 条
  • [41] Effect of grain size on the microstructure and mechanical properties of friction stir welded non-combustive magnesium alloys
    Chen, Juan
    Fujii, Hidetoshi
    Sun, Yufeng
    Morisada, Yoshiaki
    Kondoh, Katsuyoshi
    Hashimoto, Kenji
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2012, 549 : 176 - 184
  • [42] An Investigation of Microstructure and Mechanical Properties of Sn-9Zn-xCr Alloys Produced by Investment Casting Method
    Yavuzer, B.
    Ozyurek, D.
    ACTA PHYSICA POLONICA A, 2017, 131 (01) : 102 - 105
  • [43] Investigation of mechanical properties and high temperature wear resistance of CoFeNi1.5VZr0.4Six high entropy alloys optimized by Si alloying
    Jiang, Junjie
    Xin, Benbin
    Zhang, Aijun
    Han, Jiesheng
    Meng, Junhu
    TRIBOLOGY INTERNATIONAL, 2024, 200
  • [44] Study of Zr addition on the composition, crystallite size, microstructure and properties of high-performance nano Cu alloys prepared by mechanical alloying
    Han, Litao
    Liu, Jianwei
    Tang, Huaguo
    Yan, Zixiang
    MATERIALS CHEMISTRY AND PHYSICS, 2022, 290
  • [45] Investigation of mechanical, electrical conductivity, wear and corrosion performances of traditional CuNi2Si and new high performance CuNiCoSi copper based alloys
    Karakurt, Volkan
    Esen, Ismail
    Zigindere, Orcun
    Ahlatci, Hayrettin
    CANADIAN METALLURGICAL QUARTERLY, 2024,
  • [46] Effect of Zirconium Addition on the Grain Size and Mechanical Behavior of Aluminum Grain Refined by Titanium Plus Boron (Ti plus B) in the as Cast and Cold Extruded Conditions
    Zaid, A. I. O.
    Al-Qawabah, S. M. A.
    ADVANCED MATERIALS XII, 2012, 510-511 : 241 - +
  • [47] The Effect of Milling Time and Hot-Pressing on the Structural Properties and Wear Behavior of CoCrFeMnNi High-Entropy Alloys Fabricated by Mechanical Alloying
    Caner Bulut
    Fatih Yıldız
    Temel Varol
    Serhatcan Berk Akçay
    Tevfik Oğuzhan Ergüder
    High Temperature Corrosion of Materials, 2024, 101 : 225 - 249
  • [48] The Effect of Milling Time and Hot-Pressing on the Structural Properties and Wear Behavior of CoCrFeMnNi High-Entropy Alloys Fabricated by Mechanical Alloying
    Bulut, Caner
    Yildiz, Fatih
    Varol, Temel
    Akcay, Serhatcan Berk
    Erguder, Tevfik Oguzhan
    HIGH TEMPERATURE CORROSION OF MATERIALS, 2024, 101 (02) : 225 - 249
  • [49] Remarkably enhancing mechanical and degradation performance of cast MgZn1.2 alloys via small amount addition of zirconium combined with hot extrusion for orthopedic applications
    Fan, Jun
    Wu, Yongqi
    Qiu, Xin
    Tian, Zheng
    Meng, Jian
    Wan, Peng
    Li, Chen
    Dong, Baixin
    Qiu, Feng
    JOURNAL OF MATERIALS RESEARCH AND TECHNOLOGY-JMR&T, 2022, 19 : 1111 - 1119
  • [50] Effect of die parameters on the grain size, mechanical properties and fracture mechanism of extruded AZ31 magnesium alloys
    Ayer, Onder
    MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2020, 793 (793):
12345