Investigation of the Effect of Zirconium Amount on Grain Size and Wear Performance in TZM Alloys Produced by Mechanical Alloying Method

被引：1

作者：

Sirali, Haktan ^{[1
]}

Simsek, Dogan ^{[2
]}

Ozyurek, Dursun ^{[3
]}

机构：

[1] Karabuk Univ, Inst Sci, Karabuk, Turkey

[2] Natl Def Univ, Army NCO Vocat HE Sch, Balikesir, Turkey

[3] Karabuk Univ, Technol Fac, Karabuk, Turkey

来源：

TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS | 2022年 / 75卷 / 03期

关键词：

TZM alloy; Zirconium; Grain size; Wear; BEHAVIOR;

D O I：

10.1007/s12666-021-02510-4

中图分类号：

TF [冶金工业];

学科分类号：

0806 ;

摘要：

In this study, the relation between grain size, hardness and wear performance of Titanium-Zirconium-Molybdenum (TZM) alloys with different amounts (0.06, 0.07, 0.08 and 0.09 wt%) of Zr added by the mechanical alloying method was investigated. As a result of the studies, it was observed that the number of pores in the structure increased with the increase in the amount of Zr, while there was a decrease in the grain size. In the hardness and density results, it was observed that while the hardness values increased with increasing Zr amount, there was a decrease in the density values. As a result of the wear tests, the lowest weight loss at 10-30 N loads was obtained in the TZM alloy with the highest Zr added (0.09% Zr). The lowest friction coefficient in the friction coefficient results was obtained in TZM alloy with 0.09% Zr added.

引用

页码：805 / 812

页数：8

共 50 条

[21] Alloying effect on grain-size dependent deformation twinning in nanocrystalline Cu-Zn alloys
Ma, X. L.
Xu, W. Z.
Zhou, H.
Moering, J. A.
Narayan, J.
Zhu, Y. T.
PHILOSOPHICAL MAGAZINE, 2015, 95 (03) : 301 - 310
[22] Investigation of Wear Performance of Different Amount SiC Reinforcements A356 Matrix Composite Materials Produced by Semi-Solid Process Method
Simsek, Ijlal
Simsek, Dogan
Ozyurek, Dursun
JOURNAL OF POLYTECHNIC-POLITEKNIK DERGISI, 2020, 23 (04): : 1237 - 1243
[23] Investigation of the wear and corrosion behaviors of Ti5Al2.5Fe and Ti6Al4V alloys produced by mechanical alloying method in simulated body fluid environment
Simsek, Ijlal
Ozyurek, Dursun
MATERIALS SCIENCE AND ENGINEERING C-MATERIALS FOR BIOLOGICAL APPLICATIONS, 2019, 94 : 357 - 363
[24] Exchange of experience the effect of synthesis time on the wear behavior of Al–8%Ti alloy produced by mechanical alloying
D. Özyürek
S. Tekeli
T. Tuncay
R. Yilmaz
Powder Metallurgy and Metal Ceramics, 2012, 51 : 491 - 495
[25] Effect of recrystallisation and grain size on the mechanical properties of spray formed AlCuMgAg-alloys
Eschbach, L
Uggowitzer, PJ
Speidel, MO
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 1998, 248 (1-2): : 1 - 8
[26] The Effect of Porosity and Grain Size on the Phase Composition and Mechanical Properties of Zirconium-Dioxide-Based Ceramic
Savchenko, N. L.
Sablina, T. Yu.
Sevost'yanova, I. N.
Burlachenko, A. G.
Buyakova, S. P.
Kul'kov, S. N.
TECHNICAL PHYSICS LETTERS, 2018, 44 (08) : 663 - 666
[27] Effect of grain refinement on the performance of AZ80 Mg alloys during wear and corrosion
Naik, Gajanan M.
Gote, Gopal D.
Narendranath, S.
Kumar, S. S. Satheesh
ADVANCES IN MATERIALS RESEARCH-AN INTERNATIONAL JOURNAL, 2018, 7 (02): : 105 - 118
[28] Exchange of experience the effect of synthesis time on the wear behavior of Al-8%Ti alloy produced by mechanical alloying
Ozyurek, D.
Tekeli, S.
Tuncay, T.
Yilmaz, R.
POWDER METALLURGY AND METAL CERAMICS, 2012, 51 (7-8) : 491 - 495
[29] Effect of heat treatment and deformation on the grain size and mechanical properties of duralumin-type alloys
Fridlyander, IN
Berstenev, VV
Tkachenko, EA
Goloviznina, GM
Latushkina, LV
Lantsova, LP
METAL SCIENCE AND HEAT TREATMENT, 2003, 45 (7-8) : 239 - 245
[30] Effect of Heat Treatment and Deformation on the Grain Size and Mechanical Properties of Duralumin-Type Alloys
I. N. Fridlyander
V. V. Berstenev
E. A. Tkachenko
G. M. Goloviznina
L. V. Latushkina
L. P. Lantsova
Metal Science and Heat Treatment, 2003, 45 : 239 - 245

← 1 2 3 4 5 →