Effect of stacking fault energy on mechanical behavior of bulk nanocrystalline Cu and Cu alloys

被引：145

作者：

Youssef, Khaled ^{[1
]}

Sakaliyska, Miroslava ^{[2
]}

Bahmanpour, Hamed ^{[1
]}

Scattergood, Ronald ^{[1
]}

Koch, Carl ^{[1
]}

机构：

[1] N Carolina State Univ, Dept Mat Sci & Engn, Raleigh, NC 27606 USA

[2] IFW Dresden, Inst Solid State Res, Dept 12, D-01069 Dresden, Germany

来源：

ACTA MATERIALIA | 2011年 / 59卷 / 14期

基金：

美国国家科学基金会;

关键词：

Nanocrystalline; Stacking faults; Copper alloys; Mechanical properties; ULTRAFINE-GRAINED CU; ULTRAHIGH STRENGTH; TENSILE PROPERTIES; HIGH DUCTILITY; DEFORMATION; METALS; COPPER; WORK; TEMPERATURE;

D O I：

10.1016/j.actamat.2011.05.052

中图分类号：

T [工业技术];

学科分类号：

08 ;

摘要：

Twinning and dislocation slip are two major and competing modes of plastic deformation in metals and alloys. In addition to controlling the dislocation substructure in coarse grained materials, stacking fault energy (SFE) also affects the propensity to form deformation twins. However, the influence of SFE has not been fully explored in nanocrystalline materials. Here the role of SFE in deformation twinning and work hardening was systematically studied in bulk artifact-free, nanocrystalline (nc) Cu (SFE 55 mJ m(-2)), and a nc Cu-12.1 at.% Al-4.1 at.% Zn alloy (SFE 7 mJ m(-2)). The nc Cu (23 nm) and nc Cu alloy (22 nm) were synthesized using in situ consolidation during cryo and room temperature milling. Both materials showed ultra-high tensile strength, significant strain hardening, and good ductility. The nc Cu alloy exhibits a higher yield strength and lower uniform elongation (1067 +/- 20 MPa, 6.5%) than that of nc Cu (790 +/- 12 MPa, 14%). The SFE variation played a significant role in strengthening the nc Cu alloy. High resolution transmission electron microscopy analyses revealed that the low SFE of the nc Cu alloy alters the deformation mechanism from a dislocation-controlled deformation, which allows for the higher strain hardening observed in the nc Cu, to a twin-controlled deformation. (C) 2011 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

引用

页码：5758 / 5764

页数：7

共 45 条

[41] Ultratough nanocrystalline copper with a narrow grain size distribution [J].

Youssef, KM ;

Scattergood, RO ;

Murty, KL ;

Koch, CC .

APPLIED PHYSICS LETTERS, 2004, 85 (06) :929-931

[42] Determining the optimal stacking fault energy for achieving high ductility in ultrafine-grained Cu-Zn alloys [J].

Zhao, Y. H. ;

Liao, X. Z. ;

Horita, Z. ;

Langdon, T. G. ;

Zhu, Y. T. .

MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2008, 493 (1-2) :123-129

[43] Tougher ultrafine grain Cu via high-angle grain boundaries and low dislocation density [J].

Zhao, Y. H. ;

Bingert, J. F. ;

Zhu, Y. T. ;

Liao, X. Z. ;

Valiev, R. Z. ;

Horita, Z. ;

Langdon, T. G. ;

Zhou, Y. Z. ;

Lavernia, E. J. .

APPLIED PHYSICS LETTERS, 2008, 92 (08)

[44] Tailoring stacking fault energy for high ductility and high strength in ultrafine grained Cu and its alloy [J].

Zhao, Y. H. ;

Zhu, Y. T. ;

Liao, X. Z. ;

Horita, Z. ;

Langdon, T. G. .

APPLIED PHYSICS LETTERS, 2006, 89 (12)

[45]

Zhu YuntianT., 2009, BULK NANOSTRUCTURED, P89

← 1 2 3 4 5 →