Spray-wall impingement in a multi-hole GDI injector for split injection at elevated wall temperature and ambient conditions

被引:8
作者
Muddapur, Anandteerth [1 ]
Sahu, Srikrishna [1 ]
Jose, Jubin, V [1 ]
Sundararajan, T. [1 ]
机构
[1] Indian Inst Technol Madras, Dept Mech Engn, Chennai 600036, Tamil Nadu, India
关键词
Split injection; Spray impingement; Film thickness; Film mass; Film temperature; Plume height; Plume width; FLASH BOILING CONDITIONS; HIGH-PRESSURE INJECTION; COMBUSTION CHARACTERISTICS; DROPLET IMPINGEMENT; FUEL-INJECTION; ENGINE; SINGLE;
D O I
10.1016/j.tsep.2022.101367
中图分类号
O414.1 [热力学];
学科分类号
摘要
Post wall-impingement characteristics of pulsatile and split injection sprays in multi-hole Gasoline Direct Injection (GDI) are investigated. A combined experimental and numerical approach is adopted, to examine the influence of wall temperature as well as gas temperature and pressure on spray evolution. For fuel injection condition, split proportion and wall stand-off distance are not varied. The single injection case is also studied for comparison. The experiments were conducted under atmospheric conditions but for different wall temperatures, and the fuel spray was visualized using high-speed shadowgraph technique. The three-dimensional Eulerian-Lagrangian spray simulations were validated against the measured post-impingement plume width and height. Simulations were carried out to analyse spray-wall interaction process under elevated ambient temperature and pressure conditions also. Considerably smaller radial and vertical spread of the spray plume is obtained for split injection, highlighting its benefits over the single injection case. Both plume and wall film characteristics are strongly influenced by the ambient gas density and temperature rather than the wall temperature. However, time evolutions of the mass, thickness and temperature of the film are similar for both single and split cases at different operating conditions, exhibiting some interesting trends. For split injection, the vapour plumes from the two injection pulses interact. At high ambient temperatures, the peak equivalence ratio values are lower for split injection due to lower injected mass per pulse, in comparison to the single injection strategy.
引用
收藏
页数:15
相关论文
共 14 条
[1]   Spray dynamics and evaporation in a multihole GDI injector for pulsatile and split injection at elevated ambient pressure and temperature conditions [J].
Muddapur, Anandteerth ;
Jose, Jubin V. ;
Sahu, Srikrishna ;
Sundararajan, T. .
FUEL, 2020, 279
[2]   Effect of temperature on fuel adhesion under spray-wall impingement condition [J].
Luo, Hongliang ;
Nishida, Keiya ;
Uchitomi, Shintaro ;
Ogata, Youichi ;
Zhang, Wu ;
Fujikawa, Tatsuya .
FUEL, 2018, 234 :56-65
[3]   EXPERIMENTAL INVESTIGATION OF SPRAY CHARACTERISTICS OF MULTI-HOLE AND SLOT GDI INJECTORS AT VARIOUS FUEL TEMPERATURES USING CLOSELY SPACED SPLIT-INJECTION STRATEGIES [J].
Wu, Shengqi ;
Meinhart, Mark ;
Yi, Jianwen .
ATOMIZATION AND SPRAYS, 2019, 29 (12) :1109-1131
[4]   Enhanced spray-wall interaction model for port fuel injection under medium load conditions [J].
Hamid, Mohammed O. A. ;
Kunwar, Anil .
JOURNAL OF THERMAL ANALYSIS AND CALORIMETRY, 2025, 150 (01) :291-311
[5]   Effect of wall-impingement distance on fuel adhesion characteristics of split injection spray under cross-flow condition [J].
Shi, Penghua ;
Zhang, Gengxin ;
Luo, Hongliang ;
Ogata, Yoichi ;
Nishida, Keiya .
FUEL, 2024, 362
[6]   Experimental investigation of spray characteristics of multi-hole and slot gdi injectors at various fuel temperatures using closely spaced split-injection strategies [J].
Wu S. ;
Meinhart M. ;
Yi J. .
Atomization and Sprays, 2019, 29 (12) :1109-1131
[7]   Experimental study on flash-boiling spray structure of multi-hole gasoline direct injection injector in a constant volume chamber [J].
Wu, Jian ;
Du, Jiakun ;
Chen, Hong ;
Li, Yuhuai ;
Zhan, Wenfeng ;
Wu, Guangquan ;
Ye, Lin .
INTERNATIONAL JOURNAL OF SPRAY AND COMBUSTION DYNAMICS, 2020, 12
[8]   Spray development of iso-octane, ethanol, hydrous ethanol and water from a multi-hole injector under ultra cold fuel temperature conditions [J].
Aleiferis, P. G. ;
Shukla, J. ;
Brewer, M. ;
Cracknell, R. F. .
FUEL, 2021, 303
[9]   EFFECT OF INJECTION PARAMETERS ON SPRAY CHARACTERISTICS OF GAS-TO-LIQUID (GTL), BIODIESEL, AND DIESEL FUEL FOR A MULTI-HOLE INJECTOR IN A DIESEL ENGINE [J].
Choi, Kibong ;
Lee, Donggon ;
Roh, Hyun Gu ;
Lee, Chang Sik .
ATOMIZATION AND SPRAYS, 2015, 25 (12) :1107-1125
[10]   Macroscopic spray characteristics of iso-octane, ethanol, gasoline and methanol from a multi-hole injector under flash boiling conditions [J].
Badawy, Tawfik ;
Xu, Hongming ;
Li, Yanfei .
FUEL, 2022, 307