Prediction of the convective heat transfer coefficient of cutting fluid in helical drills

被引:0
作者
Pontes, Douglas Wellington [1 ]
Crichigno Filho, Joel Martins [1 ]
Berving Zdanski, Paulo Sergio [1 ]
机构
[1] Santa Catarina State Univ, Dept Mech Engn, Campus Univ, BR-89219710 Joinville, Brazil
关键词
Cutting fluid; Convective heat transfer; Temperature; Drilling; MINIMUM QUANTITY; TEMPERATURE; TOOL; CHIP; LUBRICATION; MODEL; HOLE;
D O I
10.1007/s40430-017-0904-8
中图分类号
TH [机械、仪表工业];
学科分类号
0802 ;
摘要
Environmental, economical and social factors impose the elimination or reduction of the quantity of the cutting fluids used in the machining. This trend leads to a high temperature in the cutting zone. In drilling, when the cutting fluid is not supplied through the spindle, the tool tip suffers from high temperature, leading to rapid wear. In this case, the cooling of the drill tool body can contribute significantly removing the heat generated at the tool-chip interface. However, to effectively simulate the temperature at the tool tip, the effect of the cutting fluid on tool body must be known. Hence, the aim of this work was to determine the convective heat transfer coefficient of the cutting fluid on the complex body of a helical drill. In this regard, a special experimental setup is developed, allowing the drill to remain static while the coolant nozzle rotates around providing cutting fluid. A method is developed in order to determine the temperature on the drill surface as a function of the heat enters into the drill and the temperature measured at the tool base. Experiments are carried out varying coolant nozzle rotation speed and the cutting fluid flow rate. According to the results, the cutting fluid flow rate shows to have the most significant effect on the convective heat transfer coefficient.
引用
收藏
页码:5195 / 5204
页数:10
相关论文
共 26 条
  • [1] Ber A., 1989, CIRP ANN-MANUF TECHN, V38, P69
  • [2] Bergman T.L., 2011, Introduction to Heat Transfer, DOI DOI 10.1016/J.APPLTHERMALENG.2011.03.022
  • [3] Modeling and simulation of heat input in deep-hole drilling with twist drills and MQL
    Biermann, Dirk
    Iovkov, Ivan
    [J]. 14TH CIRP CONFERENCE ON MODELING OF MACHINING OPERATIONS (CIRP CMMO), 2013, 8 : 88 - 93
  • [4] The location of the maximum temperature on the cutting edges of a drill
    Bono, M
    Ni, J
    [J]. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2006, 46 (7-8) : 901 - 907
  • [5] da Silva MB, 1998, IND LUBR TRIBOL, V50, P149
  • [6] Daniel C. M., 1996, Proceedings of the Japan-USA Symposium on Flexible Automation - 1996, P1119
  • [7] Environmental friendly cutting fluids and cooling techniques in machining: a review
    Debnath, Sujan
    Reddy, Moola Mohan
    Yi, Qua Sok
    [J]. JOURNAL OF CLEANER PRODUCTION, 2014, 83 : 33 - 47
  • [8] Approaches for improving cutting processes and machine tools in re-contouring
    Denkena, B.
    Boess, V.
    Nespor, D.
    Rust, F.
    Floeter, F.
    [J]. PROCEEDINGS OF THE 3RD INTERNATIONAL CONFERENCE IN THROUGH-LIFE ENGINEERING SERVICES, 2014, 22 : 239 - 242
  • [9] The influence of minimum quantity of lubrication (MQL) on cutting temperature, chip and dimensional accuracy in turning AISI-1040 steel
    Dhar, NR
    Islam, MW
    Islam, S
    Mithu, MAH
    [J]. JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2006, 171 (01) : 93 - 99
  • [10] Finite difference analysis of the thermal behaviour of coated tools in orthogonal cutting of steels
    Grzesik, W
    Bartoszuk, M
    Nieslony, P
    [J]. INTERNATIONAL JOURNAL OF MACHINE TOOLS & MANUFACTURE, 2004, 44 (14) : 1451 - 1462