Evaluation of the Taguchi method for wear behavior of Al/SiC/B4C composites

被引:32
作者
Soy, Ugur [1 ]
Ficici, Ferit [2 ]
Demir, Adem [1 ]
机构
[1] Sakarya Univ, Fac Technol, Dept Met & Mat Sci Engn, TR-54187 Sakarya, Turkey
[2] Sakarya Univ, Fac Technol, Dept Mech Engn, TR-54187 Sakarya, Turkey
关键词
Aluminum composite; wear behavior; Taguchi method; silicon carbide; boron carbide; pressure infiltration; METAL-MATRIX-COMPOSITES; DRY SLIDING WEAR; CUTTING PARAMETERS; OPTIMIZATION; FRICTION;
D O I
10.1177/0021998311410510
中图分类号
TB33 [复合材料];
学科分类号
摘要
In this study, the wear behaviors of aluminum matrix composites with an A360 matrix reinforced with silicon carbide (SiC) and boron carbide (B4C) ceramic particles using Taguchi method were investigated. Wear tests of unreinforced aluminum alloy and Al17%SiC and Al17%B4C particles reinforced aluminum composites (Al/17%SiC and Al/17%B4C, respectively) versus AISI316L stainless steel disc were carried out for a dry sliding condition in a so-called a pin-on-disc arrangement. The wear tests were realized at the sliding speeds of 0.5, 1.0, and 1.5 m s(-1) and under the loads of 10, 20, and 30 N. The obtained average specific wear rates for Al/17%B4C and Al/17%SiC composites are lower than unreinforced aluminum specific wear rate under the same test conditions. The experimental results are transformed into a signal-to-noise (S/N) ratio of using Taguchi method. Type of the material, applied load, and sliding speed exert a great effect on the specific wear rate, at 48.13%, 31.83%, and 8.77%, respectively. The estimated S/N ratio using the optimal testing parameters for specific wear rate were calculated and a good agreement was observed between the predicted and actual specific wear rate for a confidence level of 99.5%.
引用
收藏
页码:851 / 859
页数:9
相关论文
共 50 条
[41]   Mechanical properties of Al-Cu/B4C and Al-Mg/B4C metal matrix composites [J].
Ayvaz, Mehmet ;
Cetinel, Hakan .
MATERIALS TESTING, 2021, 63 (04) :350-355
[42]   Layer-Graded Cu/B4C/Graphite Hybrid Composites: Processing, Characterization, and Evaluation of Their Mechanical and Wear Behavior [J].
Prabhu, T. Ram ;
Vedantam, Srikanth .
TRIBOLOGY TRANSACTIONS, 2015, 58 (04) :718-728
[43]   Sintering and sliding wear studies of B4C-SiC composites [J].
Jamale, Sonali ;
Kumar, B. V. Manoj .
INTERNATIONAL JOURNAL OF REFRACTORY METALS & HARD MATERIALS, 2020, 87
[44]   Sliding Wear Resistance Behaviour of Al-Zn-Mg-Cu/SiC/B4C/Porcelain Composites Using Fuzzy Model and Salp Swarm Algorithm [J].
Rajak, Santosh Kumar ;
Aherwar, Amit ;
Choudhary, Roshani ;
Pathak, Vimal Kumar ;
Goyal, Ashish ;
Saxena, Kuldeep Kr. ;
Kuriachen, Basil .
TRANSACTIONS OF THE INDIAN INSTITUTE OF METALS, 2023, 76 (09) :2493-2502
[45]   Lightweight superhard B4C/SiC ceramic composites by Al4SiC4 assisted low-temperature transient liquid phase sintering [J].
Hou, Jiayi ;
Wei, Jian ;
Li, Xueting ;
Zhang, Yanbin ;
Yao, Yi ;
Lei, Wangwang ;
Zhang, Kai .
JOURNAL OF THE EUROPEAN CERAMIC SOCIETY, 2025, 45 (12)
[46]   Mechanical-wear behavior and microstructure analysis of Al2214 alloy with B4C and graphite particles hybrid composites [J].
Kambaiah, Revanna ;
Suresh, Ramappa ;
Nagaral, Madeva ;
Auradi, Virupaxi ;
Anjinappa, Chandrashekar ;
Garse, Komal ;
Pandhare, Amar Pradeep ;
Wodajo, Anteneh Wogasso .
ENGINEERING REPORTS, 2024, 6 (10)
[47]   Effects of load on tribological properties of B4C and B4C-SiC ceramics sliding against SIC balls [J].
Zhang, Wei ;
Yamashita, Seiji ;
Kita, Hideki .
JOURNAL OF ASIAN CERAMIC SOCIETIES, 2020, 8 (03) :586-596
[48]   Effect of B4C particle reinforcement on tensile properties of Al7075/B4C composites [J].
Krishnamoorthi, K. ;
Arun, A. P. ;
Muralidaran, V. Manivel .
MATERIALS TODAY-PROCEEDINGS, 2022, 62 :692-695
[49]   Dry sliding wear behavior of Al/Gr/SiC hybrid metal matrix composites by Taguchi techniques [J].
Lokesh, T. ;
Mallik, U. S. .
MATERIALS TODAY-PROCEEDINGS, 2017, 4 (10) :11175-11180
[50]   Wear Characteristics of (Al/B4C and Al/TiC) Nanocomposites Synthesized via Powder Metallurgy Method [J].
Hasan, Lamyaa Khaleel ;
Jiaad, Suaad Makki ;
Salman, Khansaa Dawood ;
Al-Maliki, Wisam Abed Kattea ;
Alobaid, Falah ;
Epple, Bernd .
APPLIED SCIENCES-BASEL, 2023, 13 (23)