Optimum processing parameters for equal channel angular pressing

被引：34
作者：
Agwa, M. A. [1 ]
Ali, M. N. [1 ]
Al-Shorbagy, Amal E. [1 ]
机构：
[1] Zagazig Univ, Fac Engn, Dept Mech Design & Prod Engn, Zagazig 44519, Egypt
来源：
MECHANICS OF MATERIALS | 2016年 / 100卷
关键词：
Equal channel angular pressing; Finite element method; Strain coefficient of variance; Channel angle; Corner angle; Friction; FINITE-ELEMENT-ANALYSIS; SIMPLE SHEAR; TOOL-ANGLES; EXTRUSION; STRAIN; ALLOYS;
D O I：
10.1016/j.mechmat.2016.06.003
中图分类号：
T [工业技术];
学科分类号：
08 ;
摘要：
This study aims to explore the optimum processing parameters for minimum strain coefficient of variance in equal channel angular pressing based on the analysis of whole steady zone. In order to design the die correctly, it is important to understand the effect of die geometry and processing parameters on the deformation behavior, strain distribution and punch load. The influences of channel angle, corner angle and friction coefficient are analyzed using finite element modeling. Analytical models are also used to validate the obtained computational solutions. Results showed that channel angle, corner angle and friction coefficient have significant influences on deformation behavior, strain coefficient of variance and punch load evolution. Among all the combinations of 7 corner angles, 6 channel angles and 6 friction coefficients (set of 252 study cases), it is found that the optimum parameters for maximum strain homogeneity correspond to channel angle phi = 90 degrees, corner angle psi = 15 degrees and friction coefficient mu = 0.3. The influence of friction coefficient on punch load is more pronounced than the influence of die geometry. (C) 2016 Elsevier Ltd. All rights reserved.
引用
收藏
页码：1 / 11
页数：11
相关论文
共 24 条
[1]  
Abaqus, 2009, AB 2009 AB 6 9 THEOR
[2]  
Agwa M.A., 2011, THESIS
[3]   Refining SiCp in reinforced Al-SiC composites using equal-channel angular pressing [J].
Arab, M. S. ;
El Mahallawy, N. ;
Shehata, F. ;
Agwa, M. A. .
MATERIALS & DESIGN, 2014, 64 :280-286
[4]   Effect of friction model in numerical analysis of equal channel angular pressing process [J].
Balasundar, I. ;
Raghu, T. .
MATERIALS & DESIGN, 2010, 31 (01) :449-457
[5]   FEM and metallurgical analysis of modified 6082 aluminium alloys processed by multipass ECAP: Influence of material properties and different process settings on induced plastic strain [J].
Cerri, E. ;
De Marco, P. P. ;
Leo, P. .
JOURNAL OF MATERIALS PROCESSING TECHNOLOGY, 2009, 209 (03) :1550-1564
[6]   Principle of equal-channel angular pressing for the processing of ultra-fine grained materials [J].
Iwahashi, Y ;
Wang, JT ;
Horita, Z ;
Nemoto, M ;
Langdon, TG .
SCRIPTA MATERIALIA, 1996, 35 (02) :143-146
[7]   Three-dimensional finite element analysis of multi-pass equal-channel angular extrusion of aluminum AA1050 with split dies [J].
Jin, Y. G. ;
Son, I. -H. ;
Kang, S. -H. ;
Im, Y. -T. .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2009, 503 (1-2) :152-155
[8]   Influence of scandium and zirconium on grain stability and superplastic ductilities in ultrafine-grained Al-Mg alloys [J].
Lee, S ;
Utsunomiya, A ;
Akamatsu, H ;
Neishi, K ;
Furukawa, M ;
Horita, Z ;
Langdon, TG .
ACTA MATERIALIA, 2002, 50 (03) :553-564
[9]   Finite element analysis of the plastic deformation zone and working load in equal channel angular extrusion [J].
Li, S ;
Bourke, MAM ;
Beyerlein, IJ ;
Alexander, DJ ;
Clausen, B .
MATERIALS SCIENCE AND ENGINEERING A-STRUCTURAL MATERIALS PROPERTIES MICROSTRUCTURE AND PROCESSING, 2004, 382 (1-2) :217-236
[10]   Analytical and finite element modeling of strain generated in equal channel angular extrusion [J].
Milind, T. R. ;
Date, P. P. .
INTERNATIONAL JOURNAL OF MECHANICAL SCIENCES, 2012, 56 (01) :26-34
123